-
Match the complete marking
Include DS3820PS7A1B1C and any revision or assembly number visible on the item. Keep the exact reference on your enquiry and quotation.
-
Check the offered item before ordering
Request available label and connector photos. Have your maintenance team compare the offered DS3820PS7A1B1C with the installed equipment and applicable GE documentation.
Technical specifications for DS3820PS7A1B1C
-
Manufacturer:General Electric
-
Product Category:General Automation
-
Spare Part Number:DS3820PS7A1B1C
-
Weight:0.3 kg
-
Tariff Code:8537101190
-
Board family:DS3820
-
Functional class:Control power supply
-
Execution:PS7A1B1C
-
Service position:Installed GE legacy control assembly
-
Electrical interface:Project-specific power and connector circuit
Information
- DS3820PS7A1B1C serves the legacy control power supply board role in a configured General Electric system; selection starts with the installed host and full marking.
Safe service: Isolate power and discharge stored energy
Acceptance: Compare restored rails and controller status
A power-supply designation does not by itself establish input range, output rails, current capacity or protection settings. The complete PS7A1B1C marking, board label and installed drawings are required before any electrical rating is assigned. Similar-looking DS3820 supply variants are not presumed interchangeable.
For replacement, record the original board position, mating connections and measured supply indications using approved safe procedures. Inspect downstream loads for short circuits and compare the restored rails and controller diagnostics after commissioning.
-
General Electric DS3820PS7A1B1C technical reference
Apter Power technical reference - PDF, 2 pages. Product identity, engineering context and applicability conditions. -
General Electric DS3820PS7A1B1C installation guide
Prepared by Apter Power - PDF, 1 page. Configuration review, safe installation and functional acceptance.
Compatibility scope: Match the PS7A1B1C execution, rack connectors, input feed and downstream load circuit to the installed system before using the board as a replacement.
-
Legacy control power
Restore supply service in a matching GE control assembly. -
Power-distribution maintenance
Support the existing rack circuit after exact board identity is verified. -
Fault isolation
Separate upstream feed, board regulation and downstream loading in the installed circuit. -
Matched replacement
Compare the complete PS7A1B1C execution and connector layout to the removed board.
Record upstream feed, protection and downstream loads.
Apply isolation and verify safe voltage before handling.
Check contacts, seating and signs of heat damage.
Investigate a shorted downstream circuit before installing a replacement.
Compare the full DS3820PS7A1B1C marking and revision.
Measure project-defined rails and affected controller diagnostics safely.
Alternative Names
Technical notes
Technical basis: GE legacy DS3820 control-system context; exact DS3820PS7A1B1C electrical ratings require the matching GE board drawing or nameplate.
Applicability: DS3820PS7A1B1C is identified as a power-supply board; no exact-model voltage or current rating is published here without a matching GE board drawing or nameplate.
FAQ View All FAQ
-
How can a no-power fault involving DS3820PS7A1B1C be localized?Separate the upstream feed, board input, regulated output and downstream load using the approved circuit drawing.
-
Why should a failed downstream load be checked before replacing DS3820PS7A1B1C?A load short can damage a new supply board or immediately reproduce the fault.
-
What measurements should be recorded before removing DS3820PS7A1B1C?Capture permitted input and output rail readings, protective-device condition and controller diagnostics.
-
Does a DS3820 family match prove another supply can replace DS3820PS7A1B1C?No. Confirm full execution, connector arrangement and project electrical requirements.
-
What handling precaution matters for DS3820PS7A1B1C?Use the approved isolation, capacitor-discharge and electrostatic-discharge procedures.
-
How should abnormal heating around DS3820PS7A1B1C be investigated?Check ventilation, terminal condition, load current and signs of connector resistance under safe procedures.
-
What should be compared after installing DS3820PS7A1B1C?Compare each project-defined output rail and affected controller status with the baseline.
-
How should the correct electrical rating for DS3820PS7A1B1C be established?Read the physical nameplate and the matching GE board drawing rather than relying on another DS3820 suffix.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






