-
Match the complete marking
Include 330930-065-01-00 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330930-065-01-00 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330930-065-01-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330930-065-01-00
-
Weight:0.54 kg
-
Tariff Code:8537101190
-
Cable family:3300 XL NSv
-
Cable length:6.5 m
-
Cable armor:AISI 302 stainless-steel armor
-
Armor jacket:FEP outer jacket
-
Connector protector:Not selected
-
Approval selection:No agency approval
-
Center-conductor resistance:0.220 ohm/m
-
Shield resistance:0.066 ohm/m
-
Cable capacitance:69.9 pF/m typical
-
Connector material:Gold-plated brass
-
Minimum bend radius:25.4 mm
-
Maximum connector torque:0.56 N m; finger-tight recommended
-
Cable temperature:-52 to +177 deg C
-
Matched-system length:7 m with the documented 0.5 m probe lead
-
Matched-system range:1.5 mm
-
Matched-system scale:7.87 V/mm (200 mV/mil)
Information
- Bently Nevada 330930-065-01-00 is a 6.5 m armored NSv extension cable with FEP jacket and no connector protector that completes a calibrated NSv electrical chain.
Protection selection: FEP armor jacket; no connector protector.
Electrical construction: 69.9 pF/m typical capacitance; 0.220 ohm/m center resistance.
The selected construction uses flexible stainless-steel armor with an FEP outer jacket and no connector protector. Maintain the 25.4 mm minimum bend radius, support the armor independently and protect both joints from contamination.
Linear range, scale and frequency response belong to the complete matched NSv chain. Final acceptance restores the documented gap or bias and proves the monitor response against the machine baseline.
-
Bently Nevada 330930-065-01-00 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330930-065-01-00 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below require the documented 3300 XL NSv proximity transducer system companion components and approved machine drawing.
-
Installed signal path
Complete the coaxial path between an NSv probe and its matching Proximitor Sensor. -
Condition-monitoring service
Use the cable only with the documented transducer and monitor or conditioner family assigned to the machine channel. -
Maintenance replacement
Match conductor count, connector, length, armor and routing before disturbing the installed cable. -
Channel acceptance
Prove continuity, insulation condition and returned channel response against the approved machine baseline.
Match 330930-065-01-00, cable length, connector and conductor construction with the installed record.
Place the monitor channel and machine in the approved maintenance state before disconnecting or checking continuity.
Keep contacts dry and clean; do not use the connector or terminal lugs as a pulling point.
Preserve bend clearance, armor support, abrasion protection and separation from damaging heat or sharp edges.
Label each conductor and shield before removal, then compare end-to-end continuity with the applicable wiring drawing.
After reconnection, verify the expected monitor indication and operating response before return to service.
Alternative Names
Technical notes
Electrical relationship: Use the 6.5 m cable only where probe lead plus extension cable equals the installed NSv Proximitor length.
Mechanical relationship: Maintain the 25.4 mm minimum bend radius and protect both gold-plated ClickLoc joints from contamination and unsupported load.
Technical reference: Bently Nevada 3300 XL NSv Proximity Transducer System Datasheet, 147385 Rev. R.
FAQ View All FAQ
-
Which probe lead completes the intended chain with 330930-065-01-00?Use 330930-065-01-00 only where the installed probe lead plus 6.5 m cable equals the selected Proximitor system length; the documented target is 7 m with the documented 0.5 m probe lead.
-
How should the armored route of 330930-065-01-00 be installed?Support the AISI 302 armor independently, keep bends at or above 25.4 mm radius and prevent abrasion, crushing or tensile loading at either joint.
-
What connector checks apply before mating 330930-065-01-00?Inspect the gold-plated ClickLoc contacts for moisture, debris and damage, align them fully, connect finger-tight and do not exceed 0.56 N m.
-
How should the unprotected joints of 330930-065-01-00 be handled?Because no connector protector is selected, apply only the documented site protection method and record the final environmental sealing arrangement.
-
How should cable resistance be used when diagnosing 330930-065-01-00?Compare isolated center and shield resistance with the documented length and inspect both connectors before concluding that the Proximitor has failed.
-
What temperature boundary applies to the route of 330930-065-01-00?Keep the cable inside -52 to +177 deg C while also respecting the lower limits of the probe, connectors and Proximitor.
-
What proves the channel after replacing 330930-065-01-00?Confirm total chain length, restore the documented gap or bias and compare monitor response with the accepted machine baseline.
-
What handover data is required for 330930-065-01-00?Retain the complete marking, probe and Proximitor identities, connector condition, final route, gap or bias and operating response.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






