-
Match the complete marking
Include 330106-05-30-05-12-00 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330106-05-30-05-12-00 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330106-05-30-05-12-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330106-05-30-05-12-00
-
Weight:0.05 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Mounting configuration:Reverse mount
-
Mounting thread:M10 x 1
-
Reverse-mount base field:05
-
Reverse-mount geometry field:30
-
Total probe length:0.5 m
-
Connector:Miniature coaxial ClickLoc connector
-
Cable type:FluidLoc cable
-
Approval selection:No agency approval selected
-
Nominal probe DC resistance:7.45 +/- 0.50 ohm
-
Matched-system linear range:2.0 mm under stated reference conditions
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Proximitor supply:-17.5 to -26 V DC; 12 mA maximum without barriers
-
Proximitor output resistance:50 ohm
-
Reference target:AISI 4140 steel
Information
- The complete 330106-05-30-05-12-00 identity fixes the offered mechanical and cable configuration; installed performance still depends on the documented companion components, target and monitoring channel.
Lead selection: 0.5 m FluidLoc cable with miniature ClickLoc connector.
System boundary: Published range and scale apply to the complete matched 3300 XL 8 mm chain.
The selected 0.5 m FluidLoc lead terminates in a miniature ClickLoc coaxial connector. Preserve the documented electrical-length relationship, connector protection and independent cable support.
Published range and scale factor belong to the complete probe, extension cable and Proximitor chain. Final acceptance must restore the approved gap and prove the monitor response against the machine baseline.
-
Bently Nevada 330106-05-30-05-12-00 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330106-05-30-05-12-00 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Radial shaft vibration
Use a documented bearing location and matched transducer chain to measure shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the full expected travel inside the characterized working region. -
Phase or speed reference
Use only with an approved once-per-turn target feature and a monitoring channel configured for phase or speed reference. -
Installed-channel maintenance
Preserve the exact probe, cable, Proximitor, mounting geometry and machine baseline recorded for the existing channel.
Match every field of 330106-05-30-05-12-00 with the installed spare-parts record before removal or installation.
Keep the probe tip, connector and cable free from impact, moisture, metal chips and unsupported loading.
Record reach, thread engagement, lock position and target relationship before disturbing the installed component.
Maintain the approved bend radius, separation and strain relief; do not twist, kink or crush the coaxial path.
Use the approved stopped-machine procedure to restore gap or bias and verify expected target travel.
Verify the as-left electrical reading, monitor indication and operating response before return to service.
Alternative Names
Technical notes
Installation relationship: Confirm the M10 x 1 reverse-mount sleeve, rear access, mechanical datum and target travel before removal.
Electrical boundary: Use the 0.5 m FluidLoc lead only inside the documented 3300 XL 8 mm total-length chain.
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet, 141194 Rev. AN.
FAQ View All FAQ
-
Which installed mounting arrangement belongs with 330106-05-30-05-12-00?Use 330106-05-30-05-12-00 only where the machine drawing specifies an M10 x 1 reverse-mount probe and provides the required rear access, sleeve support and target clearance.
-
How should the 0.5 m lead of 330106-05-30-05-12-00 be matched?Add only the documented extension cable required by the installed 3300 XL 8 mm system length, then verify the Proximitor length code and monitor assignment.
-
What connector controls apply to 330106-05-30-05-12-00?Keep the ClickLoc interface and FluidLoc cable clean, dry and supported; confirm full engagement without twisting or loading the probe lead.
-
How should matched-system performance be proved for 330106-05-30-05-12-00?Restore the approved gap or bias with the stopped machine, verify monitor indication and compare the operating response with the accepted machine baseline.
-
What evidence should be captured before removing 330106-05-30-05-12-00?Photograph the complete 330106-05-30-05-12-00 marking, installed datum, connector, cable route and companion electronics. Record the stopped-machine baseline for the 3300 XL 8 mm reverse-mount proximity probe.
-
How should connector integrity be checked on 330106-05-30-05-12-00?Isolate the channel, inspect the coaxial contacts for moisture and damage, verify continuity only with an approved method, and provide strain relief so the connector carries no cable load.
-
What commissioning record is required for 330106-05-30-05-12-00?Retain the exact markings, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and the accepted operating response.
-
When should 330106-05-30-05-12-00 be withheld from service?Do not release the channel if the complete identity, mechanical fit, cable construction, connector, approval marking or measured response differs from the approved installed record.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studies-
GE IS420UCSBH4A: Confirm the Offered Controller and Release TermsRead case > -
Siemens TP1500 Comfort: Check the Panel and Machine ProjectRead case > -
28 ABB BRC410 Units: Ready to Inspect, Collected on Order DayRead case > -
Honeywell FC-RUSIO-3224 Delivered for an Oman Government ProjectRead case >
You May Also Like
Product Browsing History
-
330106-05-30-05-12-00Product Details -
330101-00-40-05-02-05Product Details -
3300/50-02-01-00-00Product Details -
330910-00-05-10-02-00Product Details -
330101-00-16-10-02-05Product Details -
330101-00-20-90-02-05Product Details -
330101-00-49-90-12-05Product Details -
22810-00-10-10-02Product Details -
3500/15 106M1079-01Product Details -
81724-00-08-10-02Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.


