-
Match the complete marking
Include 330104-00-05-05-11-05 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330104-00-05-05-11-05 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330104-00-05-05-11-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330104-00-05-05-11-05
-
Weight:0.1 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Mounting thread:M10 x 1
-
Cable armor:Stainless-steel armor
-
Unthreaded length:0 mm
-
Overall case length:50 mm
-
Total probe length:0.5 m
-
Connector:Miniature coaxial ClickLoc with connector protector, FluidLoc cable
-
Approval selection:CSA, ATEX and IECEx approvals
-
Nominal probe resistance:7.45 +/- 0.50 ohm
-
Matched-system range:2.0 mm under stated reference conditions
-
Matched-system scale:7.87 V/mm (200 mV/mil)
-
Proximitor supply:-17.5 to -26 V DC; 12 mA maximum without barriers
-
Proximitor output resistance:50 ohm
-
Reference target:AISI 4140 steel
-
Measurement roles:Static position, dynamic vibration, phase reference and speed
Information
- Bently Nevada 330104-00-05-05-11-05 is the M10 x 1 armored 3300 XL 8 mm probe used as the passive sensing element in a matched eddy-current measurement chain.
Lead interface: 0.5 m; Miniature coaxial ClickLoc with connector protector, FluidLoc cable.
Matched-system role: Passive eddy-current sensing element for a complete 3300 XL 8 mm chain.
The 0.5 m lead terminates in miniature coaxial clickloc with connector protector, fluidloc cable. Preserve the probe-plus-extension-cable electrical length, keep the coaxial joint clean and dry, and support the lead independently of the connector.
The stated range and scale belong to a matched probe, extension cable and Proximitor on the reference target. Final acceptance restores the approved gap or bias and proves the monitor response against the machine baseline.
-
Bently Nevada 330104-00-05-05-11-05 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330104-00-05-05-11-05 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below require the documented 3300 XL 8 mm proximity transducer system companion components and approved machine drawing.
-
Radial shaft vibration
Use the complete matched transducer chain at a documented bearing location to observe shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the expected travel inside the characterized linear region. -
Phase reference
Use only where the installed target feature and monitoring channel are approved for once-per-turn phase reference. -
Installed-channel maintenance
Preserve the recorded probe, extension cable, Proximitor, target material, mounting geometry and monitor assignment.
Match every field of 330104-00-05-05-11-05 with the installed spare-parts and channel records.
Prevent impact, metal-particle contact and contamination at the probe tip during handling.
Record thread engagement, reach, lock position, target relationship and as-found gap or bias before removal.
Maintain the approved bend radius, connector protection and independent strain relief; do not twist the probe lead.
Use the approved stopped-machine procedure to restore the documented gap or bias.
Verify as-left electrical indication and controlled machine response against the accepted baseline.
Alternative Names
Technical notes
Installation relationship: The M10 x 1 mounting, 0 mm reach and 50 mm case define probe position.
Electrical relationship: Use the 0.5 m probe lead only within the documented 3300 XL 8 mm total-length chain.
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet, 141194 Rev. AN.
FAQ View All FAQ
-
How should the installed port be checked before fitting 330104-00-05-05-11-05?Compare the M10 x 1 mounting, 0 mm reach and 50 mm case with the machine drawing, record the as-found datum and verify that expected target travel will remain clear before the old probe is moved.
-
Which companion electronics must be retained with 330104-00-05-05-11-05?Keep 330104-00-05-05-11-05 inside the documented 3300 XL 8 mm proximity transducer system; confirm the extension-cable and Proximitor identities and the selected total system length.
-
What connector inspection is required for 330104-00-05-05-11-05?The selected interface is Miniature coaxial ClickLoc with connector protector, FluidLoc cable. Isolate the channel, inspect mating surfaces for moisture, contamination and damage, then seat and support the connection without lead strain.
-
How is the operating point restored after installing 330104-00-05-05-11-05?Use the approved stopped-machine method to restore the recorded gap or bias, then perform a bias and channel-response comparison against the approved baseline.
-
How should target material be handled when accepting 330104-00-05-05-11-05?Use the documented target material and geometry for the installed machine; a different alloy, curvature or target area can change scale and linearity.
-
What check helps separate a probe fault from a monitor fault on 330104-00-05-05-11-05?Compare the stopped-machine gap or bias at the Proximitor with the local monitor indication, then inspect the probe and cable path before substituting electronics.
-
When must 330104-00-05-05-11-05 be withheld from service?Do not release the channel if identity, mounting geometry, connector, companion electronics, target relationship or controlled response differs from the approved record.
-
What as-left evidence should be retained for 330104-00-05-05-11-05?Retain the full marking, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and controlled operating response.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330104-00-05-05-11-05Product Details -
330104-05-18-50-02-05Product Details -
2090-CSBM1DE-18AF11Product Details -
330930-060-04-05Product Details -
2711-T9C1XProduct Details -
2098-DSD-010X-DNProduct Details -
2098-DSD-010XProduct Details -
2711-T10C8XProduct Details -
6180P-15BPXPDCProduct Details -
2711-K6C16Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







