-
Match the complete marking
Compare every order group of 330101-00-20-05-01-05 with the installed item and the applicable Bently Nevada system documentation.
-
Check the offered item before ordering
Request photos of the offered 330101-00-20-05-01-05 and included items. Have the maintenance team compare them with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330101-00-20-05-01-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330101-00-20-05-01-05
-
Weight:0.08 kg
-
Tariff Code:8537101190
-
Probe system:3300 XL 8 mm
-
Probe tip family:8 mm
-
Case thread:3/8-24 UNF
-
Cable armor:without armor
-
Unthreaded length:0.0 in
-
Overall case length:2.0 in
-
Integral probe length:0.5 m
-
Cable construction:standard
-
Connector:Miniature coaxial ClickLoc, with connector protector
-
Approval option:CSA, ATEX and IECEx approvals option
-
Matching sensor:3300 XL 8 mm Proximitor Sensor
-
Matched-system scale factor:7.87 V/mm (200 mV/mil); 1 m / 5 m system value
-
Matched-system linear range:2.0 mm (80 mil); approximately 0.25 to 2.3 mm gap
-
Recommended radial gap:-9 Vdc; approximately 1.27 mm (50 mil)
-
Matched-system frequency response:0 to 10 kHz, +0/-3 dB; up to 305 m field wiring
-
Minimum flat target:15.2 mm (0.6 in) diameter
-
Minimum shaft diameter:50.8 mm (2 in); 76.2 mm (3 in) recommended
-
Probe tip diameter:8.0 mm (0.31 in)
-
Probe cable impedance:75 ohm
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 303 or 304 stainless steel
-
Standard cable temperature range:-52 to +177 deg C (-62 to +350 deg F)
Information
- The 3300 XL 8 mm probe senses shaft-to-tip gap as one part of a probe, extension cable and 3300 XL 8 mm Proximitor Sensor chain.
Case geometry: 0.0 in unthreaded; 2.0 in overall case
Connection path: 0.5 m integral lead; ClickLoc with connector protector
The integral 0.5 m probe lead terminates in a miniature coaxial ClickLoc connector with connector protector. An extension cable completes the electrical run to the 3300 XL 8 mm Proximitor Sensor; select the probe and cable lengths for the matching sensor system length. A mechanically fitting connector alone does not establish an electrically matched chain.
The final option is CSA, ATEX and IECEx approvals option. Inspect the actual marking and site classification before commissioning; retain the original monitor channel and target records. The probe must be checked in its installed chain under a controlled machine procedure rather than evaluated only as a loose component.
-
330101-00-20-05-01-05 Official Bently Nevada Reference Excerpt
Original manufacturer pages - PDF, 5 pages. Applicable system data, order-code context, interfaces and technical drawings. -
330101-00-20-05-01-05 Installation & Commissioning Guide
Apter Power engineering guide - PDF, 5 pages. Exact configuration review, safe-work boundaries, replacement sequence, diagnostics and handover record.
Application boundary: Use the manufacturer system data and the installed target geometry to decide measurement fit before replacing a probe.
-
Radial vibration and position
Confirm 3300 XL 8 mm target and monitor suitability; compare the original probe angle and bracket clearance. -
Axial position review
Check target travel and the calibrated system range before setting the mechanical gap. -
Speed or phase reference
Use a suitable target feature and compatible monitor channel; prove the event under controlled operation. -
Installed-chain replacement
Match 3/8-24 UNF, 2.0 in case, 0.5 m lead, ClickLoc option and full approval marking.
Compare every group of 330101-00-20-05-01-05 with the removed part; a shared base number does not establish equal cable or case length.
Confirm 3/8-24 UNF, 0.0 in unthreaded section and 2.0 in case against the bracket and target.
Combine the 0.5 m probe lead with the extension cable and check the 3300 XL 8 mm Proximitor Sensor system-length marking.
Keep the connector clean and verify the specified connector-protector arrangement before closing the joint.
Treat the order-code approval group as CSA, ATEX and IECEx approvals option; compare the physical label with the site requirement.
Record target condition, gap indication and a controlled dynamic or position response after fitting.
Alternative Names
Technical notes
FAQ View All FAQ
-
How should the installed measurement chain be matched when replacing 330101-00-20-05-01-05?Check the probe lead and extension cable lengths together against the 3300 XL 8 mm Proximitor Sensor marking, then compare the monitor channel configuration.
-
Why might 330101-00-20-05-01-05 fit a bracket but still produce the wrong gap reading?3/8-24 UNF fit does not verify electrical length, target material, sensor calibration or gap. Compare the full chain and measure the baseline output before return to service.
-
What should be checked before setting the gap on 330101-00-20-05-01-05?Confirm the 2.0 in case reaches the intended target without collision, then use the site-approved static target position and monitor procedure.
-
How is the ClickLoc joint on 330101-00-20-05-01-05 checked after assembly?Inspect contact cleanliness and full engagement, provide strain relief, and confirm the specified connector-protector arrangement matches the order group.
-
Can a different approval suffix be assumed equivalent to 330101-00-20-05-01-05?No. Compare the physical approval marking, installation drawing and site classification before selecting a suffix for a controlled area.
-
How should a noisy channel be isolated after installing 330101-00-20-05-01-05?Inspect target condition, ClickLoc joint, routing and shielding, then compare the probe-extension-sensor chain and monitor input under the approved diagnostic procedure.
-
What evidence is useful when accepting 330101-00-20-05-01-05 as a replacement?Retain full component markings, installed geometry, target and baseline gap reading, plus a controlled response from the monitoring channel.
-
When should the extension cable be changed along with 330101-00-20-05-01-05?Change or reselect it when the existing cable and offered probe do not provide the sensor-required electrical length, or when connector/cable condition fails inspection.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330101-00-20-05-01-05Product Details -
21504-036-068-10-02Product Details -
21504-12-28-10-02Product Details -
330171-00-32-05-01-05Product Details -
86691-01250-0400-15Product Details -
9200-06-02-10-00Product Details -
9200-02-01-10-00Product Details -
76680-00-06-50-0-2Product Details -
9200-01-05-10-00Product Details -
991-06-70-01-00Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







