-
Match the complete marking
Include 21504-036-068-10-02 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation.
-
Check the offered item before ordering
Request available label and connector photos. Have your maintenance team compare the offered 21504-036-068-10-02 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 21504-036-068-10-02
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:21504-036-068-10-02
-
Weight:0.1 kg
-
Tariff Code:8537101190
-
Product type:7200 8 mm standard-mount proximity probe
-
Probe diameter:8 mm
-
Mounting configuration:Standard mount
-
Case thread:3/8-24 UNF-2A
-
Lead armor:No armor
-
Unthreaded length:3.6 in
-
Overall case length:6.8 in
-
Total probe length:1.0 m
-
Connector:Miniature male coaxial connector
-
Probe cable impedance:95 ohm coaxial
-
Family calibrated range:2.0 mm for the matched 7200 5/8 mm system
-
Family scale factor:7.87 V/mm for a calibrated matched system
-
Family frequency response:0 to 10 kHz
-
Probe and cable temperature:-34 to +177 deg C
-
Reference target:AISI 4140 steel for published family data
Information
- The complete 21504-036-068-10-02 identity establishes the 7200 probe geometry and coaxial lead; installation requires the matching 7200 extension cable, Proximitor, target and monitor channel.
Legacy coaxial interface: The 95-ohm lead and miniature connector must remain within the documented 7200 chain.
Replacement boundary: Do not infer 3300 XL interchangeability from the 8 mm tip or connector appearance.
The 1.0 m 95-ohm coaxial lead terminates in a miniature male connector. Keep the connector clean, dry and mechanically supported, and verify that probe plus extension cable equals the electrical length required by the installed 7200 Proximitor.
Published 7200 range, scale and frequency figures belong to a calibrated complete system on the stated reference target. Restore gap using the approved stopped-machine procedure, then compare bias, monitor indication and operating response with the accepted machine baseline.
-
Bently Nevada 21504-036-068-10-02 technical reference
Apter Power reference with verified manufacturer data and exact-model applicability. -
Bently Nevada 21504-036-068-10-02 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Radial shaft vibration
Use a documented bearing location and matched transducer chain to observe shaft motion relative to the probe mounting. -
Axial position
Orient the probe toward an approved conductive thrust target and keep expected travel inside the characterized working region. -
Phase or speed reference
Use only where the installed target feature and monitoring channel are approved for once-per-turn reference measurement. -
Legacy-channel maintenance
Preserve the exact mechanical identity, cable construction, system length and companion electronics recorded for the installed channel.
Match every field of 21504-036-068-10-02 with the installed record before removal or installation.
Keep the tip, connector and cable free from impact, moisture, metal chips and unsupported loading.
Record reach, thread engagement, locknut position and target relationship before disturbing the installed component.
Maintain the approved bend radius, separation and strain relief; do not twist or crush the coaxial path.
Use the approved stopped-machine procedure and confirm expected target travel remains in the documented working region.
Verify the as-left electrical reading, monitor indication and operating response before return to service.
Alternative Names
Technical notes
Installation relationship: Use the 3.6 in unthreaded reach, 6.8 in case and recorded locknut datum to rebuild the installed position.
Electrical boundary: Use only with the documented 7200 extension cable and Proximitor combination.
Technical reference: Bently Nevada 7200 Proximity Transducer Systems 5 mm and 8 mm original datasheet.
FAQ View All FAQ
-
How should the 3.6 in unthreaded reach of 21504-036-068-10-02 be verified?Compare the port, sleeve and target drawing with the 3.6 in unthreaded section and 6.8 in case before the old probe is removed.
-
Which extension cable and Proximitor can be used with 21504-036-068-10-02?Only the documented 7200 family components and total system length should be used. Confirm all three markings before disconnection.
-
How should the miniature coaxial connector of 21504-036-068-10-02 be protected?Keep the interface clean and dry, fully seat the connector, provide strain relief and apply only the approved environmental protection method.
-
Can 21504-036-068-10-02 be mixed with a 3300 XL 8 mm component?No cross-family substitution should be assumed. A conversion requires a documented complete-system review of probe, cable, Proximitor, monitor and target.
-
How should the complete marking of 21504-036-068-10-02 be recorded before removal?Photograph the full order identity, installed position, companion components and cable route. Save the stopped-machine baseline so the replacement can be returned to the same documented configuration.
-
Which companion-component check is required before installing 21504-036-068-10-02?Confirm the probe, extension cable and Proximitor or signal conditioner identities as a documented chain. Connector fit alone does not establish electrical calibration.
-
How should cable and connector integrity be tested for 21504-036-068-10-02?Isolate the channel, inspect contacts for moisture, contamination and damage, verify continuity and insulation with an approved method, and support the cable so the connector carries no tensile load.
-
What commissioning evidence should be retained for 21504-036-068-10-02?Retain complete markings, mechanical datum, companion identities, wiring or chain-length checks, as-left measurements and the operating response accepted by the maintenance authority.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studies-
28 ABB BRC410 Units: Ready to Inspect, Collected on Order DayRead case > -
Honeywell FC-RUSIO-3224 Delivered for an Oman Government ProjectRead case > -
Honeywell FC-RUSIO-3224 Delivered for an Oman Government ProjectRead case > -
Invensys 3806E Sourcing: Five Spares Delivered to the CustomerRead case >
You May Also Like
Product Browsing History
-
21504-036-068-10-02Product Details -
21504-12-28-10-02Product Details -
330171-00-32-05-01-05Product Details -
86691-01250-0400-15Product Details -
9200-06-02-10-00Product Details -
9200-02-01-10-00Product Details -
76680-00-06-50-0-2Product Details -
9200-01-05-10-00Product Details -
991-06-70-01-00Product Details -
9324-RLD700NXENEProduct Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.


