-
Match the complete marking
Provide the complete 330904-00-10-05-02-05 marking, installed-position photographs and all companion-component identities used by the current arrangement.
-
Check the offered item before ordering
Compare the offered 330904-00-10-05-02-05 execution, connections and included items with the approved drawing and manufacturer documentation before ordering.
Technical specifications for 330904-00-10-05-02-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330904-00-10-05-02-05
-
Weight:0.1 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL NSv
-
Base probe number:330904
-
Mounting thread:M8 x 1
-
Lead protection:Flexible stainless-steel armor
-
Unthreaded length:0 mm
-
Overall case length:100 mm
-
Total probe length:0.5 m
-
Connector and cable option:02 - ClickLoc connector, standard cable
-
Agency approval option:05 - Multiple approvals
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 303 or 304 stainless steel
-
Cable construction:75 ohm triaxial, FEP insulated
-
Matched-system linear range:1.5 mm (60 mils), matched NSv system
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Recommended operating gap:1.0 mm (40 mils)
-
Frequency response:0 to 10 kHz, +0/-3 dB
-
Reference target:13 mm flat target minimum; AISI 4140 reference steel
-
Probe temperature range:-52 to +177 deg C
-
Minimum cable bend radius:25.4 mm
Information
- The full 330904-00-10-05-02-05 order identity defines M8 x 1, armored, 0 mm unthreaded reach, 100 mm case, a 0.5 m standard lead and multiple approvals for its matched 3300 XL NSv measurement chain.
Protected lead routing: Flexible stainless-steel armor adds mechanical protection along the probe lead while still requiring independent routing support.
Matched signal path: The calibrated probe lead remains an electrical component of the complete transducer system.
Flexible stainless-steel armor adds mechanical protection along the probe lead while still requiring independent routing support. The standard FEP-insulated triaxial lead preserves the documented electrical relationship within the matched transducer chain. The order code does not include a factory-installed connector protector, so joint protection must follow the approved installation plan.
Published range, scale and frequency data apply to the complete matched 3300 XL NSv probe, extension cable and Proximitor Sensor under the stated target and calibration conditions. Commissioning therefore includes live gap, runout and receiving-channel response checks.
330904-00-10-05-02-05 Official Datasheet Excerpt
Bently Nevada 3300 XL NSv Proximity Transducer System Datasheet 147385 Rev. R. Selected original pages covering the applicable product identity, technical data and system relationship.330904-00-10-05-02-05 Installation & Verification Guide
Model-specific field guide for identity capture, installed-fit checks, controlled replacement, commissioning and handover.
Application scope: Use 330904-00-10-05-02-05 for non-contacting shaft vibration, axial position or phase-reference measurement where its documented thread, reach, case and matched-system geometry fit the approved machine drawing.
Radial shaft vibration
Use 330904-00-10-05-02-05 where the M8 x 1 body and 100 mm case reproduce the documented bearing-housing geometry.Axial position measurement
Confirm target flatness, available travel and the 0 mm reach before setting the operating gap.Mechanically exposed routing
Support the armored lead independently through exposed machine areas.Restricted-clearance points
Apply the NSv small-target and probe-spacing guidance in counterbores and narrow views.
Photograph 330904-00-10-05-02-05 and confirm every option block before removal.
Record 0 mm reach, 100 mm case, insertion position and locknut location.
Do not twist, pull or suspend the probe by its armor or ferrule.
Keep mating faces clean and add only the approved environmental protection required by the installation.
Combine the 0.5 m probe lead only with the extension cable and Proximitor Sensor selected for the intended system length.
Set live gap and compare static bias, runout and measurement response with the accepted baseline.
Alternative Names
Technical notes
Exact configuration: M8 x 1, armored, 0 mm unthreaded reach, 100 mm case; 0.5 m lead; ClickLoc connector, standard cable; multiple approvals
System boundary: Range, scale and frequency values belong to the complete matched 3300 XL NSv transducer chain, not the probe alone
Technical reference: Bently Nevada 3300 XL NSv Proximity Transducer System Datasheet 147385 Rev. R
FAQ View All FAQ
-
How should the 0 mm reach of 330904-00-10-05-02-05 be reproduced?Record the installed datum and locknut position before removal, then confirm the 100 mm case places the tip at the same approved target gap.
-
What does the M8 x 1 execution of 330904-00-10-05-02-05 require at the machine port?Inspect thread form, engagement, sleeve clearance and target alignment; matching nominal diameter alone is not sufficient.
-
How does the armored lead affect routing of 330904-00-10-05-02-05?Support the armor independently, avoid ferrule loading and do not use the armor as a pulling member.
-
What connection protection is selected on 330904-00-10-05-02-05?Option 02 does not include a factory-installed protector; use the approved site protection only where required.
-
How is total electrical length controlled for 330904-00-10-05-02-05?The probe contributes 0.5 m; add only the documented extension cable that matches the intended Proximitor Sensor system length.
-
Which target assumptions apply to 330904-00-10-05-02-05?Published performance uses the stated AISI 4140 reference target; verify target size, material, flatness and nearby conductive geometry for the actual machine.
-
How should 330904-00-10-05-02-05 be checked after installation?Set the approved live gap, confirm stable bias, then compare slow-roll runout and the intended vibration, position or phase response with the accepted record.
-
What does approval option 05 mean for 330904-00-10-05-02-05?The order code selects the documented multiple-approval execution; the installed circuit must still follow the applicable certified drawing.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330904-00-10-05-02-05Product Details -
330105-02-12-05-02-CNProduct Details -
330901-00-90-05-02-00Product Details -
330104-02-21-10-01-00Product Details -
330103-00-05-10-02-CNProduct Details -
330104-16-21-05-01-05Product Details -
330103-00-05-05-02-05Product Details -
330908-22-31-10-01-05Product Details -
330101-00-27-10-02-05Product Details -
330104-00-03-10-01-00Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.





