-
Match the complete marking
Provide the complete 330104-16-21-05-01-05 marking, installed-position photographs and all companion-component identities used by the current arrangement.
-
Check the offered item before ordering
Compare the offered 330104-16-21-05-01-05 execution, connections and included items with the approved drawing and manufacturer documentation before ordering.
Technical specifications for 330104-16-21-05-01-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330104-16-21-05-01-05
-
Weight:0.12 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Base probe number:330104
-
Mounting thread:M10 x 1
-
Lead protection:Flexible stainless-steel armor
-
Unthreaded length:160 mm
-
Overall case length:210 mm
-
Total probe length:0.5 m
-
Connector and cable option:01 - ClickLoc connector with protector, standard cable
-
Agency approval option:05 - Multiple approvals
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 303 or 304 stainless steel
-
Cable construction:75 ohm triaxial, FEP insulated
-
Matched-system linear range:2.0 mm (80 mils), matched 3300 XL 8 mm system
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Recommended operating gap:Approximately 1.27 mm at -9 V DC
-
Frequency response:0 to 10 kHz, +0/-3 dB
-
Reference target:15.2 mm flat target minimum; AISI 4140 reference steel
-
Probe temperature range:-52 to +177 deg C
-
Minimum cable bend radius:25.4 mm
Information
- The full 330104-16-21-05-01-05 order identity defines M10 x 1, armored, 160 mm unthreaded reach, 210 mm case, a 0.5 m standard lead and multiple approvals for its matched 3300 XL 8 mm measurement chain.
Protected lead routing: Flexible stainless-steel armor adds mechanical protection along the probe lead while still requiring independent routing support.
Protected field connection: A connector protector is included with the ClickLoc connection for environmental protection of the probe-to-extension joint.
Flexible stainless-steel armor adds mechanical protection along the probe lead while still requiring independent routing support. The standard FEP-insulated triaxial lead preserves the documented electrical relationship within the matched transducer chain. A connector protector is included with the ClickLoc connection for environmental protection of the probe-to-extension joint.
Published range, scale and frequency data apply to the complete matched 3300 XL 8 mm probe, extension cable and Proximitor Sensor under the stated target and calibration conditions. Commissioning therefore includes live gap, runout and receiving-channel response checks.
330104-16-21-05-01-05 Official Datasheet Excerpt
Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet 141194 Rev. AN. Selected original pages covering the applicable product identity, technical data and system relationship.330104-16-21-05-01-05 Installation & Verification Guide
Model-specific field guide for identity capture, installed-fit checks, controlled replacement, commissioning and handover.
Application scope: Use 330104-16-21-05-01-05 for non-contacting shaft vibration, axial position or phase-reference measurement where its documented thread, reach, case and matched-system geometry fit the approved machine drawing.
Radial shaft vibration
Use 330104-16-21-05-01-05 where the M10 x 1 body and 210 mm case reproduce the documented bearing-housing geometry.Axial position measurement
Confirm target flatness, available travel and the 160 mm reach before setting the operating gap.Mechanically exposed routing
Support the armored lead independently through exposed machine areas.Matched-system maintenance
Retain the probe, extension cable and Proximitor Sensor identities as one calibrated chain.
Photograph 330104-16-21-05-01-05 and confirm every option block before removal.
Record 160 mm reach, 210 mm case, insertion position and locknut location.
Do not twist, pull or suspend the probe by its armor or ferrule.
Seat the connection finger-tight and refit the supplied protector without pinching the cable.
Combine the 0.5 m probe lead only with the extension cable and Proximitor Sensor selected for the intended system length.
Set live gap and compare static bias, runout and measurement response with the accepted baseline.
Alternative Names
Technical notes
Exact configuration: M10 x 1, armored, 160 mm unthreaded reach, 210 mm case; 0.5 m lead; ClickLoc connector with protector, standard cable; multiple approvals
System boundary: Range, scale and frequency values belong to the complete matched 3300 XL 8 mm transducer chain, not the probe alone
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet 141194 Rev. AN
FAQ View All FAQ
-
How should the 160 mm reach of 330104-16-21-05-01-05 be reproduced?Record the installed datum and locknut position before removal, then confirm the 210 mm case places the tip at the same approved target gap.
-
What does the M10 x 1 execution of 330104-16-21-05-01-05 require at the machine port?Inspect thread form, engagement, sleeve clearance and target alignment; matching nominal diameter alone is not sufficient.
-
How does the armored lead affect routing of 330104-16-21-05-01-05?Support the armor independently, avoid ferrule loading and do not use the armor as a pulling member.
-
What connection protection is selected on 330104-16-21-05-01-05?Option 01 supplies a protector over the ClickLoc joint; install it only after the clean connector is fully seated.
-
How is total electrical length controlled for 330104-16-21-05-01-05?The probe contributes 0.5 m; add only the documented extension cable that matches the intended Proximitor Sensor system length.
-
Which target assumptions apply to 330104-16-21-05-01-05?Published performance uses the stated AISI 4140 reference target; verify target size, material, flatness and nearby conductive geometry for the actual machine.
-
How should 330104-16-21-05-01-05 be checked after installation?Set the approved live gap, confirm stable bias, then compare slow-roll runout and the intended vibration, position or phase response with the accepted record.
-
What does approval option 05 mean for 330104-16-21-05-01-05?The order code selects the documented multiple-approval execution; the installed circuit must still follow the applicable certified drawing.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330104-16-21-05-01-05Product Details -
330103-00-05-05-02-05Product Details -
330908-22-31-10-01-05Product Details -
330101-00-27-10-02-05Product Details -
330104-00-03-10-01-00Product Details -
330103-00-08-05-02-05Product Details -
330103-06-20-10-02-00Product Details -
330104-10-16-05-01-00Product Details -
330103-00-05-10-01-05Product Details -
330102-00-25-10-02-05Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






