-
Match the complete marking
Include the complete 330103-00-05-10-01-05 marking and photographs of the installed connection and mounting position.
-
Check the offered item before ordering
Request available-unit label and connector photographs. Have your maintenance team compare the offered 330103-00-05-10-01-05 with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330103-00-05-10-01-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330103-00-05-10-01-05
-
Weight:0.06 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Mounting thread:M10 x 1
-
Armor:Without armor
-
Unthreaded length:0 mm
-
Overall case length:50 mm
-
Total probe length:1.0 m
-
Connector and cable option:01 - ClickLoc with protector, standard cable
-
Agency approval option:05 - CSA, ATEX and IECEx
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 303 or 304 stainless steel
-
Cable construction:75 ohm triaxial, FEP insulated
-
System linear range:2.0 mm (80 mils), matched 3300 XL 8 mm system
-
System scale factor:7.87 V/mm (200 mV/mil)
-
Recommended radial-vibration gap:-9 V DC; approximately 1.27 mm
-
Frequency response:0 to 10 kHz, +0/-3 dB
-
Standard probe temperature:-52 to +177 deg C
-
Minimum cable bend radius:25.4 mm
Information
- The probe uses an unarmored metric body, zero unthreaded length and a connector-protected standard cable for a matched 3300 XL 8 mm chain.
Protected detachable joint: A factory-installed protector shields the finger-tight ClickLoc connection.
Unarmored flexible routing: The standard FEP lead supports controlled routing where external armor is not required.
The 1.0 m FEP-insulated lead ends in a miniature ClickLoc connector with a protector. The standard cable must be routed within the documented bend radius and combined with the correct extension cable and Proximitor Sensor length.
The 2.0 mm system range and 7.87 V/mm scale factor apply to a matched 3300 XL 8 mm chain. Set operating gap from live voltage and verify both static bias and dynamic response after service.
330103-00-05-10-01-05 Official Datasheet Excerpt
Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet 141194 Rev. AN. Selected original pages covering the applicable product family, technical data and ordering information.330103-00-05-10-01-05 Installation & Verification Guide
Apter Power field guide covering identity capture, installed relationships, controlled replacement, commissioning and handover.
Application scope: Use it for documented 8 mm eddy-current measurement points with an M10 x 1 port and controlled unarmored lead routing.
Metric shaft-vibration points
Install in an approved M10 x 1 port with the required target geometry and system gap.Compact axial-position mounts
Confirm the 50 mm case and zero-unthreaded geometry before reproducing the locknut datum.Protected connector routing
Use the fitted protector where the probe-to-extension joint is exposed to the machinery environment.Interchangeable XL service
Retain only approved 3300 XL 8 mm components in the calibrated signal chain.
Confirm 00, 05, 10, 01 and 05 with the full 330103 base number.
Keep thread engagement at or below the documented 15 mm maximum.
Prevent abrasion, tension and movement at the probe-case transition.
Clean both connector faces and confirm the locking click before fitting the protector.
Match the probe, extension cable and Proximitor Sensor as one system.
Retain gap voltage, runout and channel response after commissioning.
Alternative Names
Technical notes
Exact configuration: M10 x 1 unarmored probe, 0 mm unthreaded length, 50 mm case, 1.0 m standard lead, connector protector and multiple approvals
System boundary: Use only within a correctly matched 3300 XL 8 mm transducer chain
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet 141194 Rev. AN
FAQ View All FAQ
-
Why is the zero-unthreaded geometry important for 330103-00-05-10-01-05?It places the M10 x 1 thread immediately behind the sensing end, so the installed sleeve and locknut position must match the 50 mm case.
-
What is the maximum thread engagement for 330103-00-05-10-01-05?The documented maximum for the M10 x 1 case is 15 mm; longer engagement can bind the probe.
-
How should the unarmored lead of 330103-00-05-10-01-05 be routed?Maintain the 25.4 mm bend radius, provide strain relief and keep the lead away from abrasion and unsupported movement.
-
What does connector option 01 provide on 330103-00-05-10-01-05?It provides the miniature ClickLoc connection with a factory-installed protector over the standard cable joint.
-
Which approval set is selected by 330103-00-05-10-01-05?Code 05 selects the documented CSA, ATEX and IECEx option; installation remains subject to the approved circuit drawing.
-
How is the 1.0 m lead of 330103-00-05-10-01-05 matched?Choose the extension cable and 3300 XL Proximitor Sensor so the complete electrical length equals the intended system length.
-
What confirms correct gap after replacing 330103-00-05-10-01-05?Set the operating point near -9 V DC, then confirm available travel and compare runout or vibration response with the prior baseline.
-
Which parts of 330103-00-05-10-01-05 should be photographed before removal?Capture the complete marking, locknut datum, thread engagement, cable route, protector and both companion-component labels.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330103-00-05-10-01-05Product Details -
330102-00-25-10-02-05Product Details -
330102-00-27-10-02-05Product Details -
330102-00-52-10-02-00Product Details -
84661-12Product Details -
2711P-T15C21D8SProduct Details -
3500/15 106M1079-01Product Details -
21504-000-032-10-02Product Details -
330130-085-02-CNProduct Details -
330930-065-04-05Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







