-
Match the complete marking
Include 330103-00-08-05-02-05 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330103-00-08-05-02-05 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330103-00-08-05-02-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330103-00-08-05-02-05
-
Weight:0.08 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Thread:M10 x 1
-
Cable armor:No armor
-
Unthreaded length:0 mm
-
Overall case length:80 mm
-
Total probe length:0.5 m
-
Connector:Miniature coaxial ClickLoc, standard cable
-
Approval selection:CSA, ATEX and IECEx approvals selected
-
Nominal probe DC resistance:7.45 +/- 0.50 ohm
-
Matched-system linear range:2.0 mm under stated reference conditions
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Proximitor supply:-17.5 to -26 V DC; 12 mA maximum without barriers
-
Proximitor output resistance:50 ohm
-
Reference target:AISI 4140 steel
-
Measurement roles:Static position, dynamic vibration, phase reference and speed
Information
- Bently Nevada 330103-00-08-05-02-05 is an 8 mm eddy-current proximity probe for the 3300 XL family; when it is used in the standard 5 m matched system, the platform meets API 670 requirements for mechanical configuration, linear range, accuracy and temperature stability.
Lead and connector: 0.5 m; Miniature coaxial ClickLoc, standard cable.
System boundary: Scale, linearity and gap belong to the complete matched 3300 XL 8 mm chain.
The 0.5 m lead uses miniature coaxial clickloc, standard cable. Preserve the electrical-length relationship to the installed Proximitor, keep the coaxial interface clean and dry, and support the cable independently of the connector.
Published range and scale factor belong to the probe, extension cable and Proximitor as a matched system on the reference target. Final acceptance must restore the approved gap and prove the monitor response against the machine baseline.
-
Bently Nevada 330103-00-08-05-02-05 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330103-00-08-05-02-05 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Radial shaft vibration
Use a documented bearing location and matched transducer chain to measure shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the full expected travel inside the characterized working region. -
Phase or speed reference
Use only with an approved once-per-turn target feature and a monitoring channel configured for phase or speed reference. -
Installed-channel maintenance
Preserve the exact probe, cable, Proximitor, mounting geometry and machine baseline recorded for the existing channel.
Match every field of 330103-00-08-05-02-05 with the installed spare-parts record before removal or installation.
Keep the probe tip, connector and cable free from impact, moisture, metal chips and unsupported loading.
Record reach, thread engagement, lock position and target relationship before disturbing the installed component.
Maintain the approved bend radius, separation and strain relief; do not twist, kink or crush the coaxial path.
Use the approved stopped-machine procedure to restore gap or bias and verify expected target travel.
Verify the as-left electrical reading, monitor indication and operating response before return to service.
Alternative Names
Technical notes
Installation relationship: The M10 x 1 mounting, 0 mm unthreaded reach and 80 mm case establish the probe position.
Electrical boundary: The 0.5 m probe and miniature coaxial clickloc, standard cable must remain within the documented 3300 XL 8 mm chain.
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet, 141194 Rev. AN.
FAQ View All FAQ
-
Which extension cable and Proximitor belong with 330103-00-08-05-02-05?Use 330103-00-08-05-02-05 in a documented 3300 XL 8 mm chain whose probe plus extension cable equals the selected system length. Confirm every component marking before disconnection.
-
How should the 80 mm case of 330103-00-08-05-02-05 be checked mechanically?Compare the M10 x 1 port depth, 0 mm unthreaded reach, lock position and target travel with the approved machine drawing.
-
What does the connector selection on 330103-00-08-05-02-05 require during installation?The selected interface is Miniature coaxial ClickLoc, standard cable. Keep it clean and dry, fully seat it, and add only the approved environmental protection and strain relief.
-
How should the matched-system performance of 330103-00-08-05-02-05 be proved?Restore the approved gap, confirm bias and monitor indication, then compare the operating response with the accepted machine baseline; do not treat the probe as a standalone voltage source.
-
What evidence should be captured before removing 330103-00-08-05-02-05?Photograph the complete 330103-00-08-05-02-05 marking, installed datum, connector, cable route and companion electronics. Record the stopped-machine baseline for the 3300 XL 8 mm proximity probe.
-
How should connector integrity be checked on 330103-00-08-05-02-05?Isolate the channel, inspect the coaxial contacts for moisture and damage, verify continuity only with an approved method, and provide strain relief so the connector carries no cable load.
-
What commissioning record is required for 330103-00-08-05-02-05?Retain the exact markings, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and the accepted operating response.
-
When should 330103-00-08-05-02-05 be withheld from service?Do not release the channel if the complete identity, mechanical fit, cable construction, connector, approval marking or measured response differs from the approved installed record.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330103-00-08-05-02-05Product Details -
330103-06-20-10-02-00Product Details -
330104-10-16-05-01-00Product Details -
330103-00-05-10-01-05Product Details -
330102-00-25-10-02-05Product Details -
330102-00-27-10-02-05Product Details -
330102-00-52-10-02-00Product Details -
84661-12Product Details -
2711P-T15C21D8SProduct Details -
3500/15 106M1079-01Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







