-
Match the complete marking
Include the complete 330104-10-16-05-01-00 marking and photographs of the installed connection and mounting position.
-
Check the offered item before ordering
Request available-unit label and connector photographs. Have your maintenance team compare the offered 330104-10-16-05-01-00 with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330104-10-16-05-01-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330104-10-16-05-01-00
-
Weight:0.16 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Mounting thread:M10 x 1
-
Armor:With armor
-
Unthreaded length:100 mm
-
Overall case length:160 mm
-
Total probe length:0.5 m
-
Connector and cable option:01 - ClickLoc with protector, standard cable
-
Agency approval option:00 - Not required
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 303 or 304 stainless steel
-
Cable construction:75 ohm triaxial, FEP insulated
-
System linear range:2.0 mm (80 mils), matched 3300 XL 8 mm system
-
System scale factor:7.87 V/mm (200 mV/mil)
-
Recommended radial-vibration gap:-9 V DC; approximately 1.27 mm
-
Frequency response:0 to 10 kHz, +0/-3 dB
-
Standard probe temperature:-52 to +177 deg C
-
Minimum cable bend radius:25.4 mm
Information
- This long-reach metric execution combines stainless-steel cable armor, a protected ClickLoc connection and no agency-approval option.
Armored short lead: Mechanical cable protection is combined with a compact 0.5 m probe lead.
Protected service joint: The ClickLoc connector arrives with a protector for the detachable probe-to-extension interface.
A 0.5 m standard FEP probe lead is protected by flexible stainless-steel armor and ends in a ClickLoc connection with protector. The extension cable completes the electrical length required by the Proximitor Sensor.
The published scale, range and linearity apply to the matched 3300 XL 8 mm system. Restore the mechanical datum first, then set live gap and verify the machine response against the accepted record.
330104-10-16-05-01-00 Official Datasheet Excerpt
Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet 141194 Rev. AN. Selected original pages covering the applicable product family, technical data and ordering information.330104-10-16-05-01-00 Installation & Verification Guide
Apter Power field guide covering identity capture, installed relationships, controlled replacement, commissioning and handover.
Application scope: Use it in approved M10 x 1 installations requiring 100 mm unthreaded reach and a short probe lead.
Recessed bearing housings
Use the 100 mm unthreaded section where the tip must pass through a documented sleeve or deep port.Armored short-lead routing
Protect the 0.5 m probe lead before it joins the extension cable.Metric probe replacement
Match the M10 x 1 thread, 160 mm case and locknut position exactly.Matched transducer service
Preserve total electrical length and the approved 8 mm target calibration.
Record the 100 mm unthreaded section and installed insertion depth before loosening the locknut.
Check clearance through the complete sleeve and mounting structure.
Do not rotate or pull the cable while tightening the M10 body.
Seat the ClickLoc joint and install the protector without sharp bends.
Do not claim hazardous-area approval from this order code alone.
Use live voltage and the accepted machine baseline after mechanical installation.
Alternative Names
Technical notes
Exact configuration: Armored M10 x 1 probe, 100 mm unthreaded length, 160 mm case, 0.5 m lead, connector protector and no approval option
Mechanical identity: Reach, case length and locknut position must be treated as one installed dimension set
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet 141194 Rev. AN
FAQ View All FAQ
-
Why is the 100 mm unthreaded reach critical for 330104-10-16-05-01-00?It determines where the sensing tip emerges from the sleeve or port relative to the target and cannot be replaced by a shorter geometry without review.
-
How much threaded case remains on 330104-10-16-05-01-00?The overall case is 160 mm and the unthreaded section is 100 mm; verify the actual installed locknut and sleeve arrangement rather than calculating fit from one value alone.
-
What does the 0.5 m code mean on 330104-10-16-05-01-00?It is the probe-lead total length. The extension cable must complete the intended Proximitor Sensor system length.
-
How should the armor on 330104-10-16-05-01-00 be handled during tightening?Hold and torque the probe case only; prevent the armor and lead from twisting or carrying installation load.
-
Does 330104-10-16-05-01-00 carry the multiple-approval option?No. Its final 00 code means agency approval is not required in the order code.
-
What is the connector arrangement on 330104-10-16-05-01-00?Option 01 provides a standard ClickLoc cable connection with a connector protector.
-
How is the operating gap for 330104-10-16-05-01-00 restored?Reproduce the mechanical datum, energize the matched 8 mm chain and adjust to the approved live gap-voltage target.
-
What evidence proves successful replacement of 330104-10-16-05-01-00?Retain the as-left insertion datum, gap voltage, slow-roll runout and vibration or position response with companion-component identities.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330104-10-16-05-01-00Product Details -
330103-00-05-10-01-05Product Details -
330102-00-25-10-02-05Product Details -
330102-00-27-10-02-05Product Details -
330102-00-52-10-02-00Product Details -
84661-12Product Details -
2711P-T15C21D8SProduct Details -
3500/15 106M1079-01Product Details -
21504-000-032-10-02Product Details -
330130-085-02-CNProduct Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







