-
Match the complete marking
Include 330105-02-12-05-02-CN and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330105-02-12-05-02-CN reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330105-02-12-05-02-CN
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330105-02-12-05-02-CN
-
Weight:0.05 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Mounting configuration:Reverse mount
-
Mounting thread:3/8-24 UNF
-
Fixed reverse-mount fields:02-12
-
Total probe length:0.5 m
-
Connector:Miniature coaxial ClickLoc connector
-
Cable type:standard cable
-
Approval selection:Legacy country-specific CN marking retained from delivered identity
-
Nominal probe DC resistance:7.45 +/- 0.50 ohm
-
Matched-system linear range:2.0 mm under stated reference conditions
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Proximitor supply:-17.5 to -26 V DC; 12 mA maximum without barriers
-
Proximitor output resistance:50 ohm
-
Reference target:AISI 4140 steel
Information
- 330105-02-12-05-02-CN provides the reverse-mount sensing element in a 3300 XL 8 mm eddy-current system, allowing probe installation from the rear of a compatible sleeve or housing. The matching Proximitor processes target-distance changes for shaft vibration, position or phase-reference monitoring.
Lead selection: 0.5 m standard cable with miniature ClickLoc connector.
System boundary: Published range and scale apply to the complete matched 3300 XL 8 mm chain.
The selected 0.5 m standard cable lead terminates in a miniature ClickLoc coaxial connector. Preserve the documented electrical-length relationship, connector protection and independent cable support.
Published range and scale factor belong to the complete probe, extension cable and Proximitor chain. Final acceptance must restore the approved gap and prove the monitor response against the machine baseline.
-
Bently Nevada 330105-02-12-05-02-CN official technical excerpt
Selected manufacturer pages covering the 330105 reverse-mount family, technical data and current ordering fields; the legacy CN suffix is retained without recoding. -
Bently Nevada 330105-02-12-05-02-CN engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Radial shaft vibration
Use a documented bearing location and matched transducer chain to measure shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the full expected travel inside the characterized working region. -
Phase or speed reference
Use only with an approved once-per-turn target feature and a monitoring channel configured for phase or speed reference. -
Installed-channel maintenance
Preserve the exact probe, cable, Proximitor, mounting geometry and machine baseline recorded for the existing channel.
Match every field of 330105-02-12-05-02-CN with the installed spare-parts record before removal or installation.
Keep the probe tip, connector and cable free from impact, moisture, metal chips and unsupported loading.
Record reach, thread engagement, lock position and target relationship before disturbing the installed component.
Maintain the approved bend radius, separation and strain relief; do not twist, kink or crush the coaxial path.
Use the approved stopped-machine procedure to restore gap or bias and verify expected target travel.
Verify the as-left electrical reading, monitor indication and operating response before return to service.
Alternative Names
Technical notes
Installation relationship: Confirm the 3/8-24 UNF reverse-mount sleeve, rear access, mechanical datum and target travel before removal.
Electrical boundary: Use the 0.5 m standard cable lead only inside the documented 3300 XL 8 mm total-length chain.
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet, 141194 Rev. AN.
FAQ View All FAQ
-
Which installed mounting arrangement belongs with 330105-02-12-05-02-CN?Use 330105-02-12-05-02-CN only where the machine drawing specifies a 3/8-24 UNF reverse-mount probe and provides the required rear access, sleeve support and target clearance.
-
How should the 0.5 m lead of 330105-02-12-05-02-CN be matched?Add only the documented extension cable required by the installed 3300 XL 8 mm system length, then verify the Proximitor length code and monitor assignment.
-
What connector controls apply to 330105-02-12-05-02-CN?Keep the ClickLoc interface and standard cable clean, dry and supported; confirm full engagement without twisting or loading the probe lead.
-
How should matched-system performance be proved for 330105-02-12-05-02-CN?Restore the approved gap or bias with the stopped machine, verify monitor indication and compare the operating response with the accepted machine baseline.
-
What evidence should be captured before removing 330105-02-12-05-02-CN?Photograph the complete 330105-02-12-05-02-CN marking, installed datum, connector, cable route and companion electronics. Record the stopped-machine baseline for the 3300 XL 8 mm reverse-mount proximity probe.
-
How should connector integrity be checked on 330105-02-12-05-02-CN?Isolate the channel, inspect the coaxial contacts for moisture and damage, verify continuity only with an approved method, and provide strain relief so the connector carries no cable load.
-
What commissioning record is required for 330105-02-12-05-02-CN?Retain the exact markings, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and the accepted operating response.
-
When should 330105-02-12-05-02-CN be withheld from service?Do not release the channel if the complete identity, mechanical fit, cable construction, connector, approval marking or measured response differs from the approved installed record.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330105-02-12-05-02-CNProduct Details -
330901-00-90-05-02-00Product Details -
330104-02-21-10-01-00Product Details -
330103-00-05-10-02-CNProduct Details -
330104-16-21-05-01-05Product Details -
330103-00-05-05-02-05Product Details -
330908-22-31-10-01-05Product Details -
330101-00-27-10-02-05Product Details -
330104-00-03-10-01-00Product Details -
330103-00-08-05-02-05Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






