-
Match the complete marking
Include 330103-00-05-10-02-CN and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330103-00-05-10-02-CN reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330103-00-05-10-02-CN
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330103-00-05-10-02-CN
-
Weight:0.06 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Mounting thread:M10 x 1
-
Cable armor:No armor
-
Unthreaded length:0 mm
-
Overall case length:50 mm
-
Total probe length:1.0 m
-
Connector:Miniature coaxial ClickLoc, standard cable
-
Nominal probe resistance:7.59 +/- 0.50 ohm
-
Matched-system range:2.0 mm under stated reference conditions
-
Matched-system scale:7.87 V/mm (200 mV/mil)
-
Proximitor supply:-17.5 to -26 V DC; 12 mA maximum without barriers
-
Proximitor output resistance:50 ohm
-
Reference target:AISI 4140 steel
-
Measurement roles:Static position, dynamic vibration, phase reference and speed
Information
- Bently Nevada 330103-00-05-10-02-CN is the M10 x 1 unarmored 3300 XL 8 mm probe used as the passive sensing element in a matched eddy-current measurement chain.
Lead interface: 1.0 m; Miniature coaxial ClickLoc, standard cable.
Matched-system role: Passive eddy-current sensing element for a complete 3300 XL 8 mm chain.
The 1.0 m lead terminates in miniature coaxial clickloc, standard cable. Preserve the probe-plus-extension-cable electrical length, keep the coaxial joint clean and dry, and support the lead independently of the connector.
The stated range and scale belong to a matched probe, extension cable and Proximitor on the reference target. Final acceptance restores the approved gap or bias and proves the monitor response against the machine baseline.
-
Bently Nevada 330103-00-05-10-02-CN official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330103-00-05-10-02-CN engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below require the documented 3300 XL 8 mm proximity transducer system companion components and approved machine drawing.
-
Radial shaft vibration
Use the complete matched transducer chain at a documented bearing location to observe shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the expected travel inside the characterized linear region. -
Phase reference
Use only where the installed target feature and monitoring channel are approved for once-per-turn phase reference. -
Installed-channel maintenance
Preserve the recorded probe, extension cable, Proximitor, target material, mounting geometry and monitor assignment.
Match every field of 330103-00-05-10-02-CN with the installed spare-parts and channel records.
Prevent impact, metal-particle contact and contamination at the probe tip during handling.
Record thread engagement, reach, lock position, target relationship and as-found gap or bias before removal.
Maintain the approved bend radius, connector protection and independent strain relief; do not twist the probe lead.
Use the approved stopped-machine procedure to restore the documented gap or bias.
Verify as-left electrical indication and controlled machine response against the accepted baseline.
Alternative Names
Technical notes
Installation relationship: The M10 x 1 mounting, 0 mm reach and 50 mm case define probe position.
Electrical relationship: Use the 1.0 m probe lead only within the documented 3300 XL 8 mm total-length chain.
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet, 141194 Rev. AN.
FAQ View All FAQ
-
How should the installed port be checked before fitting 330103-00-05-10-02-CN?Compare the M10 x 1 mounting, 0 mm reach and 50 mm case with the machine drawing, record the as-found datum and verify that expected target travel will remain clear before the old probe is moved.
-
Which companion electronics must be retained with 330103-00-05-10-02-CN?Keep 330103-00-05-10-02-CN inside the documented 3300 XL 8 mm proximity transducer system; confirm the extension-cable and Proximitor identities and the selected total system length.
-
What connector inspection is required for 330103-00-05-10-02-CN?The selected interface is Miniature coaxial ClickLoc, standard cable. Isolate the channel, inspect mating surfaces for moisture, contamination and damage, then seat and support the connection without lead strain.
-
How is the operating point restored after installing 330103-00-05-10-02-CN?Use the approved stopped-machine method to restore the recorded gap or bias, then perform a bias and channel-response comparison against the approved baseline.
-
How should target material be handled when accepting 330103-00-05-10-02-CN?Use the documented target material and geometry for the installed machine; a different alloy, curvature or target area can change scale and linearity.
-
What check helps separate a probe fault from a monitor fault on 330103-00-05-10-02-CN?Compare the stopped-machine gap or bias at the Proximitor with the local monitor indication, then inspect the probe and cable path before substituting electronics.
-
When must 330103-00-05-10-02-CN be withheld from service?Do not release the channel if identity, mounting geometry, connector, companion electronics, target relationship or controlled response differs from the approved record.
-
What as-left evidence should be retained for 330103-00-05-10-02-CN?Retain the full marking, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and controlled operating response.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330103-00-05-10-02-CNProduct Details -
330104-16-21-05-01-05Product Details -
330103-00-05-05-02-05Product Details -
330908-22-31-10-01-05Product Details -
330101-00-27-10-02-05Product Details -
330104-00-03-10-01-00Product Details -
330103-00-08-05-02-05Product Details -
330103-06-20-10-02-00Product Details -
330104-10-16-05-01-00Product Details -
330103-00-05-10-01-05Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







