-
Match the complete marking
Include 330500-02-01 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330500-02-01 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330500-02-01
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330500-02-01
-
Weight:0.15 kg
-
Tariff Code:8537101190
-
Measurement:Absolute bearing-housing, casing or structural vibration
-
Sensitivity:3.94 mV/mm/s (100 mV/in/s) +/-5%
-
Frequency response:4.5 Hz to 5 kHz, +/-3 dB
-
Precision frequency band:6 Hz to 2.5 kHz, +/-0.9 dB
-
Velocity range:1270 mm/s (50 in/s) peak
-
Amplitude linearity:+/-2% to 152 mm/s (6 in/s) peak
-
Mounted resonant frequency:>12 kHz
-
Output bias voltage:-12 +/-3 V DC
-
Dynamic output impedance:<2400 ohm
-
Broadband noise floor:0.004 mm/s rms nominal
-
Maximum signal cable length:305 m under stated cable conditions
-
Operating temperature:-55 to +121 deg C
-
Case material:316L stainless steel
-
Connector:2-pin MIL-C-5015, hermetically sealed
-
Mounting torque:32 to 46 kg cm maximum
-
Sensor diameter:25.3 mm
-
Sensor height:63.2 mm
-
Typical sensor mass:142 g
-
Mounting adapter selection:M8 x 1 mounting adapter
-
Approval/configuration marking:CSA/US/C approval
Information
- 330500-02-01 combines a piezoelectric sensing element with embedded integration electronics to produce a velocity-proportional signal from absolute machine-casing vibration. It is applied on rigid bearing housings, casings or structural points connected to a compatible current-limited vibration monitor input.
Selected mounting: M8 x 1 mounting adapter; mounting surface and torque govern high-frequency coupling.
Electrical output: 3.94 mV/mm/s sensitivity with -12 +/-3 V DC output bias.
The selected m8 x 1 mounting adapter must be seated on a rigid prepared surface. Preserve connector polarity, cable support and the monitor current-limiting arrangement, and keep mounting torque within 32 to 46 kg cm.
Published sensitivity and frequency response assume the stated loading and mounting conditions. Final acceptance should compare the installed velocity response with the established machine baseline across a controlled operating state.
-
Bently Nevada 330500-02-01 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330500-02-01 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Radial shaft vibration
Use a documented bearing location and matched transducer chain to measure shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the full expected travel inside the characterized working region. -
Phase or speed reference
Use only with an approved once-per-turn target feature and a monitoring channel configured for phase or speed reference. -
Installed-channel maintenance
Preserve the exact probe, cable, Proximitor, mounting geometry and machine baseline recorded for the existing channel.
Match every field of 330500-02-01 with the installed spare-parts record before removal or installation.
Keep the probe tip, connector and cable free from impact, moisture, metal chips and unsupported loading.
Record reach, thread engagement, lock position and target relationship before disturbing the installed component.
Maintain the approved bend radius, separation and strain relief; do not twist, kink or crush the coaxial path.
Use the approved stopped-machine procedure to restore gap or bias and verify expected target travel.
Verify the as-left electrical reading, monitor indication and operating response before return to service.
Alternative Names
Technical notes
Installation relationship: Use the selected m8 x 1 mounting adapter on a rigid bearing-housing or casing surface; flexible brackets can attenuate or distort the response.
Electrical boundary: The sensor incorporates embedded electronics and requires the documented current-limited monitor input, cable loading and polarity.
Technical reference: Bently Nevada 330500 Velomitor Piezo-velocity Sensor Datasheet, 141632 Rev. V.
FAQ View All FAQ
-
Where should 330500-02-01 be mounted?Use a rigid, prepared bearing-housing, casing or structural location that transfers the vibration of interest; avoid thin covers, flexible brackets and painted or uneven surfaces.
-
How should the mounting interface of 330500-02-01 be prepared?Confirm the selected m8 x 1 mounting adapter, clean and flatten the mounting surface, apply the approved installation method, and keep torque within 32 to 46 kg cm.
-
What electrical checks apply to 330500-02-01?Confirm the current-limited input and polarity, record the unloaded bias, inspect the 2-pin MIL-C-5015 connector, and keep field cable loading within the documented channel design.
-
How should the response of 330500-02-01 be accepted?Compare the local velocity reading and monitor indication at a controlled operating state with the approved machine baseline; investigate resonance, loose mounting or cable motion before release.
-
What evidence should be captured before removing 330500-02-01?Photograph the complete 330500-02-01 marking, installed datum, connector, cable route and companion electronics. Record the stopped-machine baseline for the Velomitor piezo-velocity sensor.
-
How should connector integrity be checked on 330500-02-01?Isolate the channel, inspect the coaxial contacts for moisture and damage, verify continuity only with an approved method, and provide strain relief so the connector carries no cable load.
-
What commissioning record is required for 330500-02-01?Retain the exact markings, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and the accepted operating response.
-
When should 330500-02-01 be withheld from service?Do not release the channel if the complete identity, mechanical fit, cable construction, connector, approval marking or measured response differs from the approved installed record.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







