-
Match the complete marking
Include 330905-00-25-05-01-05 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330905-00-25-05-01-05 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330905-00-25-05-01-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330905-00-25-05-01-05
-
Weight:0.05 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL NSv
-
Mounting thread:M10 x 1
-
Cable armor:No armor
-
Unthreaded length:0 mm
-
Overall case length:250 mm
-
Total probe length:0.5 m
-
Connector:Miniature coaxial ClickLoc with connector protector, standard cable
-
Approval selection:Multiple approvals
-
Nominal probe resistance:4.0 +/- 0.5 ohm
-
Cable impedance:75 ohm
-
Probe tip material:PPS
-
Case material:AISI 304 stainless steel
-
Connector material:Gold-plated brass
-
Probe tensile strength:220 N maximum
-
Matched-system lengths:5 m or 7 m
-
Matched-system range:1.5 mm
-
Matched-system scale:7.87 V/mm (200 mV/mil)
-
Recommended gap:1.0 mm
-
Frequency response:0 to 10 kHz, +0/-3 dB typical
Information
- Bently Nevada 330905-00-25-05-01-05 is a M10 x 1 unarmored NSv probe for restricted mounting and small-target measurement in a matched NSv chain.
Lead interface: 0.5 m lead; Miniature coaxial ClickLoc with connector protector, standard cable.
NSv role: Reduced side-view and small-target measurement in a matched 5 m or 7 m chain.
The 0.5 m, 75-ohm probe lead terminates in miniature coaxial clickloc with connector protector, standard cable. Probe lead plus extension cable must equal the 5 m or 7 m Proximitor selection, so cable length is part of the calibrated configuration.
NSv range and scale are characterized for the complete matched system. Acceptance also checks target size, nearby conductive surfaces, probe spacing, restored gap or bias and the monitor response for the machine.
-
Bently Nevada 330905-00-25-05-01-05 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330905-00-25-05-01-05 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below require the documented 3300 XL NSv proximity transducer system companion components and approved machine drawing.
-
Radial shaft vibration
Use the complete matched transducer chain at a documented bearing location to observe shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the expected travel inside the characterized linear region. -
Phase reference
Use only where the installed target feature and monitoring channel are approved for once-per-turn phase reference. -
Installed-channel maintenance
Preserve the recorded probe, extension cable, Proximitor, target material, mounting geometry and monitor assignment.
Match every field of 330905-00-25-05-01-05 with the installed spare-parts and channel records.
Prevent impact, metal-particle contact and contamination at the probe tip during handling.
Record thread engagement, reach, lock position, target relationship and as-found gap or bias before removal.
Maintain the approved bend radius, connector protection and independent strain relief; do not twist the probe lead.
Use the approved stopped-machine procedure to restore the documented gap or bias.
Verify as-left electrical indication and controlled machine response against the accepted baseline.
Alternative Names
Technical notes
Mechanical relationship: The M10 x 1 mounting, 0 mm reach and 250 mm case control probe position.
System relationship: The 0.5 m probe lead must be combined with the correct NSv extension cable and Proximitor total-length option.
Technical reference: Bently Nevada 3300 XL NSv Proximity Transducer System Datasheet, 147385 Rev. R.
FAQ View All FAQ
-
How should the installed port be checked before fitting 330905-00-25-05-01-05?Compare the M10 x 1 thread, 0 mm unthreaded reach and 250 mm case with the machine drawing, record the as-found datum and verify that expected target travel will remain clear before the old probe is moved.
-
Which companion electronics must be retained with 330905-00-25-05-01-05?Keep 330905-00-25-05-01-05 inside the documented 3300 XL NSv proximity transducer system; confirm the extension-cable and Proximitor identities and the selected total system length.
-
What connector inspection is required for 330905-00-25-05-01-05?The selected interface is Miniature coaxial ClickLoc with connector protector, standard cable. Isolate the channel, inspect mating surfaces for moisture, contamination and damage, then seat and support the connection without lead strain.
-
How is the operating point restored after installing 330905-00-25-05-01-05?Use the approved stopped-machine method to restore the recorded gap or bias, then perform target-size, bias and monitor-response checks against the accepted baseline.
-
How should target material be handled when accepting 330905-00-25-05-01-05?Use the documented target material and geometry for the installed machine; a different alloy, curvature or target area can change scale and linearity.
-
What check helps separate a probe fault from a monitor fault on 330905-00-25-05-01-05?Compare the stopped-machine gap or bias at the Proximitor with the local monitor indication, then inspect the probe and cable path before substituting electronics.
-
When must 330905-00-25-05-01-05 be withheld from service?Do not release the channel if identity, mounting geometry, connector, companion electronics, target relationship or controlled response differs from the approved record.
-
What as-left evidence should be retained for 330905-00-25-05-01-05?Retain the full marking, small-target geometry, companion identities, probe spacing, as-left gap or bias and operating response.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330905-00-25-05-01-05Product Details -
330901-00-90-10-01-05Product Details -
128987-130-00-00Product Details -
330930-060-01-05Product Details -
330930-065-01-00Product Details -
330500-04-01Product Details -
2098-DSD-010XProduct Details -
2711-T10C8XProduct Details -
6180P-15BPXPDCProduct Details -
2711-K6C16Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







