-
Match the complete marking
Compare the full 330901-00-10-05-02-00 marking, 1/4-28 UNF case, 1.0 in case length and 0.5 m lead with the installed probe.
-
Check the offered item before ordering
Confirm the mating NSv extension cable, Proximitor Sensor, connector and total system length before ordering.
Technical specifications for 330901-00-10-05-02-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330901-00-10-05-02-00
-
Weight:0.05 kg
-
Tariff Code:8537101190
-
Probe thread:1/4-28 UNF
-
Cable armor:None
-
Unthreaded case length:0.0 in
-
Overall case length:1.0 in
-
Total probe length:0.5 m
-
Connector:Miniature coaxial ClickLoc; standard cable; no separate protector
-
Agency approval option:00 — not required
-
Matched-system linear range:1.5 mm (60 mil)
-
Matched-system average scale factor:7.87 V/mm (200 mV/mil)
-
Matched-system recommended gap:1.0 mm (40 mil)
Information
- The 330901-00-10-05-02-00 probe carries the NSv sensing tip through a fully threaded 1.0 in case to the measurement point. Its 0.5 m lead reaches the mating NSv extension cable within a calibrated transducer chain.
Lead and termination: 0.5 m total length with a miniature ClickLoc connector and standard cable.
System fit: Unarmored 330901 probe for a matched 3300 XL NSv measurement loop.
The 0.5 m total length is selected by code 05. Connector code 02 provides a miniature coaxial ClickLoc connection with standard cable and without a separate connector protector. Preserve the correct matched NSv extension cable and Proximitor Sensor.
Approval code 00 does not request the multiple-approval option. The 1.5 mm range and 7.87 V/mm average scale factor belong to a calibrated matched NSv transducer system, not the standalone probe. Verify the assembled chain against its accepted machine baseline.
330901-00-10-05-02-00 NSv Technical Datasheet Excerpt
Manufacturer probe-ordering and matched-system technical pages. PDF · 5 pages.330901-00-10-05-02-00 Installation & Verification Guide
Apter Power guide to marking, system length, connector care, gap and channel verification. PDF · 3 pages.
Application scope: NSv systems suit small shafts and restricted side-view locations when target size, material, installed geometry and complete system length match the application.
Small-shaft radial monitoring
Use an approved matched NSv chain at a fluid-film bearing where shaft diameter or side-view clearance restricts a standard probe.Axial position channel
Place the tip at an approved thrust target and verify the available linear gap and target width.Speed or phase reference
Use a suitable target feature and monitor channel when the complete NSv loop is configured for pulse observation.Existing NSv probe replacement
Retain the 1/4-28 port, 1.0 in case envelope, 0.5 m lead and compatible cable/sensor combination.
Match all five option fields of 330901-00-10-05-02-00 before removal or installation.
Keep the NSv tip and connector away from impact, conductive debris, moisture and unsupported cable load.
Verify the machine drawing, shaft size and nearby side-view metal for the intended sensing position.
Record the probe lead and NSv extension cable so the specified total electrical length remains matched.
Use the approved stopped-machine procedure and check the complete system output against the accepted gap baseline.
After controlled restoration, compare the bias, dynamic reading and alarm response with the retained channel record.
Alternative Names
Technical notes
Matched-chain boundary: Do not treat the probe-only listing as a complete calibrated transducer system.
Case and thread: The 0.0 in unthreaded section leaves the 1.0 in case threaded; verify engagement and tip reach.
Lead selection: Code 05 specifies 0.5 m total probe length, separate from the complete NSv system length.
Connector handling: Code 02 uses standard cable and a ClickLoc connection without a separate protector.
FAQ View All FAQ
-
How does 330901-00-10-05-02-00 connect to the NSv measuring chain?Its miniature ClickLoc terminates the standard probe lead. Connect it to the correctly specified NSv extension cable and Proximitor Sensor, then confirm total electrical length.
-
Why does 330901-00-10-05-02-00 require a matched NSv extension cable?The probe, cable and Proximitor are calibrated as a system. A mismatched cable length can shift the gap-voltage relationship and invalidate the measurement.
-
What mounting check matters for 330901-00-10-05-02-00?Compare the 1/4-28 UNF thread, fully threaded 1.0 in case and planned tip reach with the machine port drawing and installed locknut position.
-
How should side-view metal be assessed around 330901-00-10-05-02-00?Check the approved target and nearby conductive surfaces against NSv installation clearances; the small-target advantage does not remove the need for geometric verification.
-
Can 330901-00-10-05-02-00 be connected to an ordinary 3300 XL 8 mm Proximitor?Use the approved NSv Proximitor and cable combination for this NSv probe; confirm the existing sensor identity before interchange.
-
What does the standard-cable ClickLoc selection change on 330901-00-10-05-02-00?Code 02 selects the miniature connector without a separate protector. Protect the mating surfaces and ensure a secure, clean connection.
-
How is a working gap verified after installing 330901-00-10-05-02-00?With the machine in its approved state, compare the complete NSv loop voltage and monitor indication with the accepted gap procedure and baseline.
-
Which evidence should be retained after replacing 330901-00-10-05-02-00?Record the full marking, mechanical position, companion cable/sensor identities, as-left gap response and channel indication.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330901-00-10-05-02-00Product Details -
330103-10-15-10-02-05Product Details -
330103-00-10-10-02-05Product Details -
330881-28-05-080-00-02Product Details -
330103-17-23-05-02-05Product Details -
330101-00-30-15-02-00Product Details -
330101-00-20-05-01-05Product Details -
21504-036-068-10-02Product Details -
21504-12-28-10-02Product Details -
330171-00-32-05-01-05Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







