-
Match the complete marking
Provide the complete 330730-040-01-00 marking, installed-position photographs and all companion-component identities used by the current arrangement.
-
Check the offered item before ordering
Compare the offered 330730-040-01-00 execution, connections and included items with the approved drawing and manufacturer documentation before ordering.
Technical specifications for 330730-040-01-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330730-040-01-00
-
Weight:0.14 kg
-
Tariff Code:8537101190
-
Cable family:3300 XL 11 mm extension cable
-
Cable length:4.0 m (13.1 ft)
-
Connector and cable option:01 - Armored standard cable
-
Agency approval option:00 - Not required
-
Conductor construction:75 ohm triaxial, FEP insulated
-
Armor material:Flexible AISI 302 stainless steel
-
Armor jacket:FEP outer jacket
-
Cable capacitance:69.9 pF/m typical
-
Center-conductor resistance:1.0 +/- 0.25 ohm for 4.0 m
-
Jacket resistance:0.3 +/- 0.1 ohm for 4.0 m
-
Operating and storage temperature:-52 to +177 deg C
-
Minimum bend radius:25.4 mm
-
Connector contact material:Gold-plated brass
-
Connector torque:Finger-tight ClickLoc connection
-
Matched system lengths:5 m or 9 m including probe lead and extension cable
Information
- The 330730-040-01-00 code selects a 4.0 m standard electrical cable with stainless-steel armor and no agency-approval option for the 11 mm transducer chain.
Armored route protection: Flexible stainless-steel armor adds mechanical protection along exposed machinery and conduit paths.
Serviceable ClickLoc interfaces: Finger-tight probe and sensor connections support controlled field replacement without special connector tooling.
Flexible stainless-steel armor protects the FEP-insulated triaxial cable, but the run still requires independent support, controlled bend radius and clean ClickLoc connections at both ends.
The probe lead plus this 4.0 m extension cable must equal the Proximitor Sensor total length. Acceptance includes identity, connector condition, resistance or continuity where appropriate, stable gap voltage and expected channel response.
330730-040-01-00 Official Datasheet Excerpt
Bently Nevada 3300 XL 11 mm Proximity Transducer System Datasheet 146256 Rev. T. Selected original pages covering the applicable product identity, technical data and system relationship.330730-040-01-00 Installation & Verification Guide
Model-specific field guide for identity capture, installed-fit checks, controlled replacement, commissioning and handover.
Application scope: Use 330730-040-01-00 only in a documented 3300 XL 11 mm system whose probe lead and Proximitor Sensor are matched to the 4.0 m armored cable execution.
Five-metre system completion
Combine the 4.0 m extension cable with the documented 1.0 m probe lead for a 5 m electrical chain.Armored machinery routing
Use independent supports where the cable crosses exposed machine or conduit transitions.Long-range 11 mm measurement
Maintain the calibrated 11 mm signal path for radial vibration or axial position channels.Controlled cable replacement
Retain probe geometry while exchanging only the verified cable construction and length.
Measure the intended route and verify the 4.0 m electrical length before installation.
Do not suspend cable weight from either ClickLoc connector or use the armor as a pulling member.
Inspect contact surfaces before making finger-tight connections.
Route every turn at or above 25.4 mm and avoid crushing the armored section.
Add the probe lead and 4.0 m cable before selecting the 5 m or 9 m Proximitor Sensor.
After reconnection, check stable gap, runout and expected dynamic or position indication.
Alternative Names
Technical notes
Exact configuration: 4.0 m armored standard 3300 XL 11 mm extension cable; no agency-approval option
Calibration relationship: Cable length, capacitance, resistance and connectors are part of the complete matched transducer chain
Technical reference: Bently Nevada 3300 XL 11 mm Proximity Transducer System Datasheet 146256 Rev. T
FAQ View All FAQ
-
Why is the 4.0 m length of 330730-040-01-00 electrically important?Probe lead plus extension cable must equal the Proximitor Sensor total length; changing cable length changes the calibrated chain.
-
What does option 01 add to 330730-040-01-00?It selects the standard FEP electrical cable with flexible stainless-steel armor, without a connector protector.
-
Which probe normally forms a 5 m chain with 330730-040-01-00?A compatible 1.0 m 3300 XL 11 mm probe lead combines with this 4.0 m extension cable to total 5 m.
-
How should the armor of 330730-040-01-00 be supported?Clamp the route independently so cable weight and machine vibration do not load the connector bodies or armor ferrules.
-
What resistance values support a bench check of 330730-040-01-00?The 4.0 m cable has documented center-conductor resistance of 1.0 +/- 0.25 ohm and jacket resistance of 0.3 +/- 0.1 ohm.
-
Does 330730-040-01-00 include connector protectors?No. Option 01 is armored standard cable without protectors; add only the approved protection required by the installation.
-
Why can 330730-040-01-00 not be replaced with generic triaxial cable?Its calibrated length, capacitance, resistance, ClickLoc interfaces and mechanical construction are defined parts of the 11 mm system.
-
What final proof is required after fitting 330730-040-01-00?Confirm both connections, stable gap voltage, expected monitor indication and the intended vibration or position response.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







