-
Match the complete marking
Include 21504-000-008-10-02 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 21504-000-008-10-02 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 21504-000-008-10-02
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:21504-000-008-10-02
-
Weight:0.04 kg
-
Tariff Code:8537101190
-
Transducer series:7200 Series 5 mm and 8 mm
-
Probe tip diameter:8 mm
-
Mounting configuration:Standard mount
-
Mounting thread:3/8-24 UNF
-
Lead armor:No armor
-
Unthreaded length:0.0 in
-
Overall case length:0.8 in
-
Total probe length:1.0 m
-
Connector:Miniature male coaxial connector
-
Connector option code:02
-
Measurement principle:Non-contact eddy-current proximity measurement
-
Matched-system calibrated range:2.0 mm (80 mil)
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Matched-system frequency response:0 to 10 kHz; -5% at 10 kHz
-
Reference target:AISI 4140 steel
-
Proximitor supply:-17.5 to -26 V DC; 12 mA maximum
-
Probe and cable temperature range:-34 to +177 deg C
-
Companion electronics:Matching 7200 Series 5 mm/8 mm Proximitor and extension cable
Information
- 21504-000-008-10-02 is the non-contact eddy-current sensing element of a legacy 7200 Series 5 mm/8 mm proximity transducer system. With its matching extension cable and Proximitor, the chain measures static shaft position and dynamic shaft-relative vibration.
Selected mechanics: 3/8-24 UNF; 0.0 in unthreaded; 0.8 in case.
Lead selection: 1.0 m unarmored lead with miniature male coaxial connector.
The 1.0 m lead terminates in a miniature male coaxial connector. Preserve the installed extension-cable and Proximitor identity, protect the unarmored cable route, and do not mix the legacy 7200 electrical relationship with a 3300 XL chain.
The 2.0 mm range and 7.87 V/mm scale factor are matched-system values on the stated reference target. Commissioning must restore the documented gap or bias and prove the complete 7200 channel against the recorded machine baseline.
-
Bently Nevada 21504-000-008-10-02 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 21504-000-008-10-02 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Radial shaft vibration
Use a documented bearing location and matched transducer chain to measure shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the full expected travel inside the characterized working region. -
Phase or speed reference
Use only with an approved once-per-turn target feature and a monitoring channel configured for phase or speed reference. -
Installed-channel maintenance
Preserve the exact probe, cable, Proximitor, mounting geometry and machine baseline recorded for the existing channel.
Match every field of 21504-000-008-10-02 with the installed spare-parts record before removal or installation.
Keep the probe tip, connector and cable free from impact, moisture, metal chips and unsupported loading.
Record reach, thread engagement, lock position and target relationship before disturbing the installed component.
Maintain the approved bend radius, separation and strain relief; do not twist, kink or crush the coaxial path.
Use the approved stopped-machine procedure to restore gap or bias and verify expected target travel.
Verify the as-left electrical reading, monitor indication and operating response before return to service.
Alternative Names
Technical notes
Installation relationship: The 3/8-24 UNF mounting, 0.0 in unthreaded section and 0.8 in case establish the installed probe position.
System boundary: Use the 1.0 m unarmored lead only with the documented 7200 extension cable and Proximitor of the appropriate total system length.
Technical reference: Bently Nevada 7200 Proximity Transducer Systems 5 mm and 8 mm Technical/Ordering Information, L5001.
FAQ View All FAQ
-
Which transducer family must remain with 21504-000-008-10-02?Keep 21504-000-008-10-02 inside the documented 7200 Series 5 mm/8 mm probe, extension-cable and Proximitor chain; do not substitute a 3300 or 3300 XL companion component.
-
How should the 0.8 in case of 21504-000-008-10-02 be checked?Compare the 3/8-24 UNF port, 0.0 in unthreaded section, 0.8 in case, probe datum and target travel with the approved machine drawing.
-
How should the 1.0 m lead of 21504-000-008-10-02 be handled?Protect the unarmored coaxial lead from abrasion and unsupported pull, and keep the miniature male coaxial connector clean, dry and free of side load.
-
What proves acceptable operation after replacing 21504-000-008-10-02?Restore the documented gap or bias using the approved stopped-machine procedure, then verify monitor indication and operating response against the accepted 7200-channel baseline.
-
What evidence should be captured before removing 21504-000-008-10-02?Photograph the complete 21504-000-008-10-02 marking, installed datum, connector, cable route and companion electronics. Record the stopped-machine baseline for the 7200 Series 8 mm standard-mount proximity probe.
-
How should connector integrity be checked on 21504-000-008-10-02?Isolate the channel, inspect the coaxial contacts for moisture and damage, verify continuity only with an approved method, and provide strain relief so the connector carries no cable load.
-
What commissioning record is required for 21504-000-008-10-02?Retain the exact markings, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and the accepted operating response.
-
When should 21504-000-008-10-02 be withheld from service?Do not release the channel if the complete identity, mechanical fit, cable construction, connector, approval marking or measured response differs from the approved installed record.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
21504-000-008-10-02Product Details -
330101-00-52-10-02-00Product Details -
330102-00-25-10-02-05Product Details -
330102-00-27-10-02-05Product Details -
330102-00-52-10-02-00Product Details -
84661-12Product Details -
2711P-T15C21D8SProduct Details -
3500/15 106M1079-01Product Details -
21504-000-032-10-02Product Details -
330130-085-02-CNProduct Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







