-
Match the complete marking
Include 330930-065-02-00 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330930-065-02-00 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330930-065-02-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330930-065-02-00
-
Weight:0.42 kg
-
Tariff Code:8537101190
-
Cable family:3300 XL NSv
-
Cable length:6.5 m
-
Cable armor:AISI 302 stainless-steel armor
-
Armor jacket:No FEP outer jacket selected
-
Connector protector:Not selected
-
Agency approval option:Not required
-
Cable DC resistance - center:0.220 ohm/m
-
Cable DC resistance - shield:0.066 ohm/m
-
Cable capacitance:69.9 pF/m typical
-
Connector material:Gold-plated brass
-
Minimum bend radius:25.4 mm
-
Maximum connector torque:0.56 N m; finger-tight recommended
-
Cable temperature range:-52 to +177 deg C, operating and storage
-
Supported matched-system length:7 m with the documented 0.5 m probe lead
-
Matched-system linear range:1.5 mm under stated reference conditions
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
Information
- 330930-065-02-00 forms part of the calibrated impedance path between a 3300 XL NSv probe and its Proximitor; its length directly determines the approved electrical system length. In the documented 7 m chain it carries the probe response to the signal conditioner for small-target and restricted-clearance measurements.
Protection selection: No FEP armor jacket and no connector protector selected.
Electrical construction: 69.9 pF/m typical capacitance; 0.220 ohm/m center-conductor resistance.
This option uses exposed stainless-steel armor without an FEP outer jacket and without a connector protector. Route it where the armor is suitable for the environment, maintain the minimum bend radius, and add site-approved joint protection when required.
Linear range, scale factor and frequency response belong to the complete matched NSv chain, not to the cable alone. Final acceptance must restore the documented gap or bias and prove the monitor response against the established machine baseline.
-
Bently Nevada 330930-065-02-00 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330930-065-02-00 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Radial shaft vibration
Use a documented bearing location and matched transducer chain to measure shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the full expected travel inside the characterized working region. -
Phase or speed reference
Use only with an approved once-per-turn target feature and a monitoring channel configured for phase or speed reference. -
Installed-channel maintenance
Preserve the exact probe, cable, Proximitor, mounting geometry and machine baseline recorded for the existing channel.
Match every field of 330930-065-02-00 with the installed spare-parts record before removal or installation.
Keep the probe tip, connector and cable free from impact, moisture, metal chips and unsupported loading.
Record reach, thread engagement, lock position and target relationship before disturbing the installed component.
Maintain the approved bend radius, separation and strain relief; do not twist, kink or crush the coaxial path.
Use the approved stopped-machine procedure to restore gap or bias and verify expected target travel.
Verify the as-left electrical reading, monitor indication and operating response before return to service.
Alternative Names
Technical notes
Electrical relationship: Use the 6.5 m cable with the documented 0.5 m NSv probe lead and 7 m Proximitor selection.
Mechanical relationship: Maintain the 25.4 mm minimum bend radius and protect both ClickLoc joints from contamination and unsupported load.
Technical reference: Bently Nevada 3300 XL NSv Proximity Transducer System Datasheet, 147385 Rev. R.
FAQ View All FAQ
-
Which probe lead completes the intended chain with 330930-065-02-00?Use the documented 0.5 m NSv probe lead so 330930-065-02-00 completes the 7 m electrical length selected on the Proximitor.
-
How should the unjacketed armor of 330930-065-02-00 be installed?Support the stainless-steel armor independently, keep bends at or above 25.4 mm radius, and prevent abrasion, crushing or tensile loading at either connector.
-
What connector checks apply before mating 330930-065-02-00?Inspect the gold-plated ClickLoc contacts for moisture, debris and damage, align them fully, connect finger-tight and do not exceed 0.56 N m.
-
How is 330930-065-02-00 accepted after replacement?Confirm the 7 m chain length, restore the documented gap or bias, compare the monitor response with the accepted baseline, and record the final cable route.
-
What evidence should be captured before removing 330930-065-02-00?Photograph the complete 330930-065-02-00 marking, installed datum, connector, cable route and companion electronics. Record the stopped-machine baseline for the 3300 XL NSv extension cable.
-
How should connector integrity be checked on 330930-065-02-00?Isolate the channel, inspect the coaxial contacts for moisture and damage, verify continuity only with an approved method, and provide strain relief so the connector carries no cable load.
-
What commissioning record is required for 330930-065-02-00?Retain the exact markings, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and the accepted operating response.
-
When should 330930-065-02-00 be withheld from service?Do not release the channel if the complete identity, mechanical fit, cable construction, connector, approval marking or measured response differs from the approved installed record.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







