Get a quick price for 330930-040-04-CN
For more information on how your data is processed and stored by Apterpower please read our privacy policy
-
Match the complete marking
Compare 330930-040-04-CN with the installed cable and applicable Bently Nevada NSv documentation.
-
Check the offered item before ordering
Request photos of 330930-040-04-CN, both connectors, jacket and armor; compare them with the installed cable and Bently Nevada documentation.
Technical specifications for 330930-040-04-CN
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330930-040-04-CN
-
Weight:0.25 kg
-
Tariff Code:8537101190
-
Cable family:330930 3300 NSv extension cable
-
Cable length:040: 4.0 m (13.1 ft)
-
Construction option:04: stainless-steel armor with FEP jacket and connector protector
-
Agency option:CN country-specific suffix; verify offered label
-
Cable impedance:75 ohm coaxial
-
Cable insulation:Fluoroethylene propylene (FEP)
-
Armor material:Flexible AISI 302 stainless steel
-
Center conductor resistance:0.220 ohm/m (0.067 ohm/ft)
-
Shield resistance:0.066 ohm/m (0.020 ohm/ft)
-
Cable capacitance:69.9 pF/m (21.3 pF/ft) typical
-
Maximum connector tensile rating:220 N (50 lb)
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Matched-system linear range:1.5 mm (60 mil); approximately 0.25 to 1.75 mm gap
-
Recommended gap setting:1.0 mm (40 mil)
-
Matched-system frequency response:0 to 10 kHz, +0/-3 dB typical; up to 305 m field wiring
-
Minimum flat target:8.9 mm (0.35 in); 13 mm (0.5 in) recommended
-
Minimum radial shaft diameter:20 mm (0.8 in); 30 mm (1.2 in) recommended
-
System supply:-17.5 to -26 Vdc without barriers; 12 mA maximum
-
Sensor output resistance:50 ohm
-
Probe cable impedance:75 ohm coaxial
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 304 stainless steel
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Matched-system linear range:1.5 mm (60 mil); approximately 0.25 to 1.75 mm gap
-
Recommended gap setting:1.0 mm (40 mil)
-
Matched-system frequency response:0 to 10 kHz, +0/-3 dB typical; up to 305 m field wiring
-
Minimum flat target:8.9 mm (0.35 in); 13 mm (0.5 in) recommended
-
Minimum radial shaft diameter:20 mm (0.8 in); 30 mm (1.2 in) recommended
-
System supply:-17.5 to -26 Vdc without barriers; 12 mA maximum
-
Sensor output resistance:50 ohm
-
Probe cable impedance:75 ohm coaxial
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 304 stainless steel
Information
Overview
Downloads
Applications / Compatibility
Product Precautions
- This extension cable completes the electrical length between a 3300 NSv probe and its matching Proximitor Sensor.
Cable length: 040 specifies 4.0 m
Construction: armored, FEP-jacketed cable with connector protector
System boundary: probe plus cable must match the NSv sensor length
Construction: armored, FEP-jacketed cable with connector protector
System boundary: probe plus cable must match the NSv sensor length
The 330930 base number identifies the 3300 NSv extension-cable family. The 040 group selects 4.0 m, and option 04 selects stainless-steel armor with an FEP jacket and connector protector. Compare both connector ends, jacket and armor with the installed cable.
The extension cable works only as one part of a calibrated NSv chain. Add its 4.0 m length to the integral probe lead and compare the total with the 5 m or 7 m Proximitor Sensor marking before setting the gap.
The CN suffix is a country-specific option whose precise approval scope must be checked on the offered label. Inspect cable routing, connector protection and shield continuity, then prove the complete monitoring channel under an approved procedure.
The extension cable works only as one part of a calibrated NSv chain. Add its 4.0 m length to the integral probe lead and compare the total with the 5 m or 7 m Proximitor Sensor marking before setting the gap.
The CN suffix is a country-specific option whose precise approval scope must be checked on the offered label. Inspect cable routing, connector protection and shield continuity, then prove the complete monitoring channel under an approved procedure.
Controller platform reference: Bently Nevada 3300 XL NSv Proximity Transducer System. Match total probe plus extension-cable length to the sensor.
The verified Bently Nevada reference excerpt covers the applicable system, ordering family and technical interfaces for 330930-040-04-CN. The Apter Power guide adds exact-code checks, installation planning, diagnostics and acceptance steps.
-
330930-040-04-CN Official Bently Nevada Reference Excerpt
Original manufacturer pages - PDF, 5 pages. Applicable system data, order-code context, interfaces and technical drawings. -
330930-040-04-CN Installation & Commissioning Guide
Apter Power engineering guide - PDF, 5 pages. Exact configuration review, safe-work boundaries, replacement sequence, diagnostics and handover record.
Use the applicable Bently Nevada system documentation and the site-approved installation procedure for 330930-040-04-CN.
System position: The cable connects the NSv probe lead to the matching Proximitor Sensor.
Compatibility boundary: Match family, electrical length, armor, jacket, connector protection and approval marking.
Compatibility boundary: Match family, electrical length, armor, jacket, connector protection and approval marking.
-
NSv chain completion
Use the 4.0 m cable only with a compatible probe lead and matching sensor length. -
Armored routing
Inspect armor, FEP jacket and bend points along the installed route. -
Connector protection
Confirm full ClickLoc engagement and the protector arrangement at both interfaces. -
Channel acceptance
Record gap indication and controlled dynamic response after reconnection.
Prepare Bently Nevada 330930-040-04-CN using the applicable installation instructions and site isolation procedure.
Read the complete cable code
Compare every group of 330930-040-04-CN with the offered label.
Check electrical length
Add 4.0 m to the probe lead and match the total to the Proximitor Sensor.
Inspect both connectors
Keep contacts clean and confirm full engagement without forcing the joint.
Protect the route
Avoid sharp bends, hot surfaces and damaged FEP or armor.
Verify the CN marking
Use the actual approval label and site classification record.
Prove the channel
Record static gap and a controlled dynamic response after installation.
Alternative Names
3300 NSv Extension Cable, complete order code 330930-040-04-CN
Bently Nevada 330930 040 04 CN complete configuration
Technical notes
Evidence boundary: The source establishes the 330930 ordering groups and NSv cable construction. System matching: Electrical performance depends on a complete matched NSv chain. Pre-purchase check: Confirm the offered label, both connectors, armor, jacket and included protectors.
FAQ View All FAQ
-
How should the 4.0 m length of 330930-040-04-CN be matched to the installed system?Add the 4.0 m cable to the probe lead and compare the total with the 5 m or 7 m Proximitor Sensor marking.
-
What does construction option 04 specify for 330930-040-04-CN?It selects stainless-steel armor with an FEP outer jacket and a connector protector.
-
Why can 330930-040-04-CN mate mechanically but still be unsuitable?Connector fit does not confirm NSv family, total electrical length, cable condition or approval marking.
-
How should the connectors on 330930-040-04-CN be inspected?Check cleanliness, complete ClickLoc engagement, strain relief and the specified protector arrangement.
-
What resistance checks can support inspection of 330930-040-04-CN?Use the published center-conductor and shield resistance-per-metre values only as family references and compare the complete installed path.
-
How should the CN suffix on 330930-040-04-CN be handled?Verify the physical approval label and applicable site record; do not infer an approval solely from the suffix.
-
What routing damage matters for 330930-040-04-CN?Inspect the FEP jacket, stainless armor, transitions, bend points and contact with hot or moving surfaces.
-
What should be retained after commissioning 330930-040-04-CN?Keep full cable and chain markings, routing photos, connector condition, gap indication and controlled channel result.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Related reading
Related cases and sourcing guidance
View all case studies
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






