-
Match the complete marking
Compare every order group of 330904-00-12-10-01-CN with the installed item and the applicable Bently Nevada system documentation.
-
Check the offered item before ordering
Request photos of the offered 330904-00-12-10-01-CN and included items. Have the maintenance team compare them with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330904-00-12-10-01-CN
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330904-00-12-10-01-CN
-
Weight:0.1 kg
-
Tariff Code:8537101190
-
Probe system:3300 XL NSv
-
Probe tip family:NSv narrow-side-view
-
Case thread:M8 x 1
-
Cable armor:with armor
-
Unthreaded length:0 mm
-
Overall case length:120 mm
-
Integral probe length:1.0 m
-
Cable construction:standard
-
Connector:Miniature coaxial ClickLoc, with connector protector
-
Approval option:CN country-specific option; verify offered label
-
Matching sensor:3300 XL NSv Proximitor Sensor
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Matched-system linear range:1.5 mm (60 mil); approximately 0.25 to 1.75 mm gap
-
Recommended gap setting:1.0 mm (40 mil)
-
Matched-system frequency response:0 to 10 kHz, +0/-3 dB typical; up to 305 m field wiring
-
Minimum flat target:8.9 mm (0.35 in); 13 mm (0.5 in) recommended
-
Minimum radial shaft diameter:20 mm (0.8 in); 30 mm (1.2 in) recommended
-
System supply:-17.5 to -26 Vdc without barriers; 12 mA maximum
-
Sensor output resistance:50 ohm
-
Probe cable impedance:75 ohm coaxial
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 304 stainless steel
Information
- The 3300 NSv probe senses shaft-to-tip gap as one part of a probe, extension cable and 3300 XL NSv Proximitor Sensor chain.
Case geometry: 0 mm unthreaded; 120 mm overall case
Connection path: 1.0 m integral lead; ClickLoc with connector protector
The integral 1.0 m probe lead terminates in a miniature coaxial ClickLoc connector with connector protector. An extension cable completes the electrical run to the 3300 XL NSv Proximitor Sensor; select the probe and cable lengths for the matching sensor system length. A mechanically fitting connector alone does not establish an electrically matched chain.
The final option is CN country-specific option; verify offered label. Inspect the actual marking and site classification before commissioning; retain the original monitor channel and target records. The probe must be checked in its installed chain under a controlled machine procedure rather than evaluated only as a loose component.
-
330904-00-12-10-01-CN Official Bently Nevada Reference Excerpt
Original manufacturer pages - PDF, 5 pages. Applicable system data, order-code context, interfaces and technical drawings. -
330904-00-12-10-01-CN Installation & Commissioning Guide
Apter Power engineering guide - PDF, 5 pages. Exact configuration review, safe-work boundaries, replacement sequence, diagnostics and handover record.
Application boundary: Use the manufacturer system data and the installed target geometry to decide measurement fit before replacing a probe.
-
Restricted-space radial vibration
Confirm 3300 XL NSv target and monitor suitability; compare the original probe angle and bracket clearance. -
Axial position review
Check target travel and the calibrated system range before setting the mechanical gap. -
Speed or phase reference
Use a suitable target feature and compatible monitor channel; prove the event under controlled operation. -
Installed-chain replacement
Match M8 x 1, 120 mm case, 1.0 m lead, ClickLoc option and full approval marking.
Compare every group of 330904-00-12-10-01-CN with the removed part; a shared base number does not establish equal cable or case length.
Confirm M8 x 1, 0 mm unthreaded section and 120 mm case against the bracket and target.
Combine the 1.0 m probe lead with the extension cable and check the 3300 XL NSv Proximitor Sensor system-length marking.
Keep the connector clean and verify the specified connector-protector arrangement before closing the joint.
Treat the order-code approval group as CN country-specific option; verify offered label; compare the physical label with the site requirement.
Record target condition, gap indication and a controlled dynamic or position response after fitting.
Alternative Names
Technical notes
FAQ View All FAQ
-
How should the installed measurement chain be matched when replacing 330904-00-12-10-01-CN?Check the probe lead and extension cable lengths together against the 3300 XL NSv Proximitor Sensor marking, then compare the monitor channel configuration.
-
Why might 330904-00-12-10-01-CN fit a bracket but still produce the wrong gap reading?M8 x 1 fit does not verify electrical length, target material, sensor calibration or gap. Compare the full chain and measure the baseline output before return to service.
-
What should be checked before setting the gap on 330904-00-12-10-01-CN?Confirm the 120 mm case reaches the intended target without collision, then use the site-approved static target position and monitor procedure.
-
How is the ClickLoc joint on 330904-00-12-10-01-CN checked after assembly?Inspect contact cleanliness and full engagement, provide strain relief, and confirm the specified connector-protector arrangement matches the order group.
-
Can a different approval suffix be assumed equivalent to 330904-00-12-10-01-CN?No. Compare the physical approval marking, installation drawing and site classification before selecting a suffix for a controlled area.
-
How should a noisy channel be isolated after installing 330904-00-12-10-01-CN?Inspect target condition, ClickLoc joint, routing and shielding, then compare the probe-extension-sensor chain and monitor input under the approved diagnostic procedure.
-
What evidence is useful when accepting 330904-00-12-10-01-CN as a replacement?Retain full component markings, installed geometry, target and baseline gap reading, plus a controlled response from the monitoring channel.
-
When should the extension cable be changed along with 330904-00-12-10-01-CN?Change or reselect it when the existing cable and offered probe do not provide the sensor-required electrical length, or when connector/cable condition fails inspection.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330904-00-12-10-01-CNProduct Details -
330901-00-10-10-02-00Product Details -
330901-00-10-05-02-00Product Details -
330103-10-15-10-02-05Product Details -
330103-00-10-10-02-05Product Details -
330881-28-05-080-00-02Product Details -
330103-17-23-05-02-05Product Details -
330101-00-30-15-02-00Product Details -
330101-00-20-05-01-05Product Details -
21504-036-068-10-02Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






