The E-ME-T-01H is an analog electronic amplifier specifically designed for single-proportional electromagnet proportional valves with displacement sensors. It utilizes a Eurocard plug-in board structure and receives external command signals to provide precise PWM current to the valve coil. It is widely used in industrial hydraulic servo control systems.
Eurocard format (DIN 41494- plug-in unit)
CE mark according to EMC directive
Electronic filters on input and output lines
E-ME-T-01H electronic drivers supply single solenoid proportional valves type ZO(R)-T with the correct current signal to align valve regulation to the error signal. The driver operates the spool's position control proportionally to the input voltage reference signals, supplying a switching current to the solenoid. Bias adjustment is available for accurate valve regulations. The electronic driver is in standard Eurocard format (1x DIN 41494 plug-in unit). A standard 32-pin backplane connector (DIN 41612 format) is utilized to securely wire all power supply inputs (24VDC), reference setpoints, enable signals, as well as the valve coil and transducer feedback loops from the rear side.
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
ATOS E-ME-T-01H Electronic Driver Module Manuals, Datasheets, Drivers, Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
Plastics Machinery
Controls the injection, mold opening, and clamping processes of injection molding and blow molding machines, precisely regulating hydraulic cylinder speed and clamping pressure to prevent flash or short shots.
Die Casting and Forging
Drives the hydraulic propulsion systems of heavy forging presses and die casting machines, precisely controlling molten metal filling speed and multi-stage forging pressure.
Metallurgical and Steel
Used in rolling mill roll gap control (AGC systems) and electric arc furnace electrode lifting, providing high-precision position and pressure regulation under harsh environments to ensure uniform steel plate thickness.
Rubber Processing Machinery
Applied in the hydraulic systems of rubber vulcanizing machines and internal mixers, precisely controlling holding pressure and temperature-related extrusion speed to improve rubber product quality.
Hydroelectric Power
Regulates the hydraulic servo systems of turbine governors (controlling guide vane opening), adjusting water inflow within milliseconds based on grid load variations to stabilize generator speed and frequency.
During installation and commissioning, you must ensure a highly stable power supply (typically 24VDC) with minimal ripple to prevent voltage fluctuations from damaging the chips. Wiring must strictly follow the manual, paying special attention to the closed-loop pins for the LVDT displacement sensor and the single solenoid, reverse connections are strictly prohibited. The amplifier should be installed in a well-ventilated electrical cabinet (standard Eurocard format). Finally, use the potentiometers or software to precisely calibrate the Bias, Gain, and Ramps to guarantee the optimal response speed and closed-loop accuracy of the proportional valve system.
The Atos E-ME-T-01H is an industrial analog electronic amplifier board manufactured in a standard Eurocard plug-in format.
Is the E-ME-T-01H a single-channel or dual-channel valve driver?
The E-ME-T-01H is strictly a single-channel driver.
Where are the wiring terminals located on the E-ME-T-01H hardware card?
All electrical interfaces on the E-ME-T-01H are processed entirely through its rear edge.
What type of bracket or mounting socket is required to install the E-ME-T-01H?
To securely install the E-ME-T-01H on a standard control cabinet rail, it must be seated into a dedicated 32-pin snap-on terminal socket base, such as the Atos E-K-32M, or inserted into a compatible multi-slot Eurocard subrack chassis.
What is the required physical slot width for the E-ME-T-01H inside a rack?
The E-ME-T-01H utilizes a slim, compact architecture that occupies exactly 1x standard slot unit (1 TE / DIN 41494 width specification) inside an industrial card cage enclosure.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
Please try to be as accurate as possible with your search.
We can quote you on 1000s of specialist parts, even if they are not listed on our website.