-
Match the complete marking
Include SL-760 and any termination suffix visible on the cell. Keep the exact reference and contact form on your enquiry and quotation.
-
Check the offered item before ordering
Request available label and terminal photos. Have your maintenance team compare the offered SL-760 with the installed holder and applicable Tadiran Batteries documentation.
Technical specifications for SL-760
-
Manufacturer:Tadiran Batteries
-
Product Category:General Automation
-
Spare Part Number:SL-760
-
Weight:0.06 kg
-
Tariff Code:8537101190
-
Cell chemistry:Lithium thionyl chloride (Li-SOCl2)
-
Cell format:AA cylindrical
-
Nominal voltage:3.6 V
-
Nominal capacity:2.2 Ah at specified test conditions
-
Nominal current:2 mA
-
Maximum continuous discharge:100 mA
-
Pulse-current capability:200 mA, subject to application conditions
-
Operating temperature:-55 to +85 deg C
-
Cell body diameter:14.7 mm nominal, catalogue drawing
-
Cell length:50.5 mm nominal, catalogue drawing
-
Cell mass:18 g, manufacturer nominal
-
Lithium content:0.65 g per cell
-
Cell volume:8 cm3
-
Anode surface area:14 cm2
-
Termination variants:/S, /T, /P, /PR and /PT listed; offered variant to be confirmed
-
Typical capacity at 20 mA:1.8 Ah to 2 V at +25 deg C (catalogue curve)
-
Typical capacity at 60 mA:1.4 Ah to 2 V at +25 deg C (catalogue curve)
Information
- Tadiran Batteries SL-760 is an AA lithium-thionyl-chloride primary cell designed for low-current operation and long service intervals. Confirm the actual terminal version and the host equipment battery specification before installation.
Nominal output: 3.6 V; 2.2 Ah at stated conditions
Available catalog terminations: /S, /T, /P, /PR and /PT
The catalog gives 2 mA nominal current, 100 mA maximum continuous discharge and 200 mA pulse-current capability under its stated conditions. Its discharge curves show that usable capacity falls as load rises, so size a replacement against the actual device duty cycle and end-voltage requirement.
The SL-760 catalog includes standard, tag, pin, radial-pin and polarized-tag termination options. Since the supplied listing does not identify a suffix, verify end-contact photographs, polarity and holder geometry before approving an exact terminal variant. The published cell operating range is -55 to +85 deg C; the complete equipment may have a narrower limit.
-
Tadiran Batteries SL-760 technical reference
Original Tadiran Batteries catalog cell-data page - PDF, 1 page. SL-760 ratings, discharge curves, dimensions and termination options. -
SL-760 engineering technical data
Manufacturer-based cell ratings, discharge behavior, termination choices and application limits. Apter Power PDF, 1 page.
Application boundary: The examples below are use contexts for a suitable low-current battery circuit. Confirm the installed equipment maker’s approved cell and replacement procedure.
-
Industrial memory backup
Use only in equipment whose battery circuit specifies an AA 3.6 V lithium primary cell and matching terminal form. Check startup load and retention requirements. -
Remote instrumentation
For long-interval, low-current installations, assess average and peak current against the SL-760 discharge curves at the site temperature. -
Controller service replacement
Compare the complete cell marking and contact form with the installed battery. Record orientation and verify equipment health after exchange. -
Standby power planning
Estimate operating life from the actual load profile and end-voltage threshold, including cold starts and any pulse duty, rather than nominal capacity alone.
SL-760 is a primary cell. Confirm the equipment does not impose charge current or use a rechargeable-cell circuit.
Compare the offered /S, /T, /P, /PR or /PT termination with the actual holder. Do not infer the suffix from AA size.
Keep contacts protected during storage and service. Do not bridge terminals with metal tools or loose parts.
Do not disassemble, incinerate, heat above 100 deg C or expose the contents to water. Follow local lithium-cell handling rules.
Inspect the holder for corrosion, fit and contact pressure; install with correct polarity and secure the cell against movement.
Measure voltage during startup and normal operation, then verify the host battery indication and record the replacement date.
Alternative Names
Technical notes
Cell selection: Match the actual SL-760 termination and polarity to the host equipment before installation.
Handling: Keep the cell dry and within the manufacturer temperature limits. Do not recharge, disassemble, incinerate or expose the contents to water.
Technical reference: Tadiran Batteries Product Data Catalogue, SL-760 AA cell; SL lithium-thionyl-chloride safety data sheet.
FAQ View All FAQ
-
How should SL-760 be evaluated for a load above its nominal current?Use the manufacturer discharge curves at the actual temperature and duty cycle. Compare required continuous and pulse current with the documented limits, then test voltage at the equipment terminals under load; nominal capacity alone is not a high-current guarantee.
-
Why might an SL-760 show voltage delay after long storage?Lithium-thionyl-chloride cells can passivate during storage. Compare the equipment startup load with the published voltage-response data and perform the approved equipment-level startup check; do not short or recharge the cell to correct a low reading.
-
Can an SL-760 with a different termination suffix be substituted without checking the holder?No. The catalog lists standard, tag, pin, radial-pin and polarized-tag versions. Match the actual contacts, polarity and mechanical clearance to the installed holder before ordering a termination variant.
-
How should an engineer interpret the 2.2 Ah rating of SL-760 in a high-drain application?The catalogue curves show available capacity varies with load and temperature. Use the expected end-voltage, duty cycle and temperature profile to estimate service life, then validate with the device manufacturer’s battery guidance.
-
What must be checked before an SL-760 is used below room temperature?Check the minimum operating temperature of both cell and host equipment and examine the discharge curve at the intended current. Confirm the system still meets its startup-voltage threshold at the coldest expected condition.
-
Can SL-760 be recharged in a holder designed for a rechargeable AA cell?No. The original manufacturer warns against recharging lithium-thionyl-chloride cells. Confirm the equipment does not apply charge current and that the holder and polarity are appropriate before installation.
-
What evidence helps identify the correct SL-760 termination when a label omits the suffix?Request clear photos of both ends and the full marking. Compare contact geometry with the manufacturer /S, /T, /P, /PR and /PT drawings; avoid selecting a suffix based only on cell size.
-
What post-installation test is appropriate after replacing an SL-760?Check polarity and retention, measure supply voltage while the equipment starts and performs its highest routine load, and verify the device’s battery or fault status. Record the installed termination and replacement date.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







