-
Match the complete marking
Include 330901-00-12-10-02-00 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330901-00-12-10-02-00 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330901-00-12-10-02-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330901-00-12-10-02-00
-
Weight:0.3 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL NSv
-
Thread:1/4-28 UNF-2A
-
Cable armor:No armor
-
Unthreaded length:0.0 in
-
Overall case length:1.2 in
-
Total probe length:1.0 m
-
Connector:Miniature coaxial ClickLoc without connector protector
-
Approval selection:No agency approval selected
-
Nominal probe DC resistance:4.2 +/- 0.5 ohm
-
Matched-system linear range:1.5 mm (60 mil)
-
Matched-system scale factor:7.87 V/mm (200 mV/mil)
-
Recommended gap:1.0 mm (40 mil)
-
Matched-system frequency response:0 to 10 kHz, +0/-3 dB typical
-
Proximitor supply:-17.5 to -26 V DC; 12 mA maximum without barriers
-
Reference target:AISI 4140 steel, 31 mm diameter or larger for stated system data
Information
- The complete 330901-00-12-10-02-00 identity fixes the offered mechanical and cable configuration; installed performance still depends on the documented companion components, target and monitoring channel.
Lead and connector: 1.0 m; Miniature coaxial ClickLoc without connector protector.
NSv application: Reduced side-view and small-target service within a matched 1.5 mm-range system.
The 1.0 m lead uses miniature coaxial clickloc without connector protector. Confirm the NSv extension cable and Proximitor identity, preserve total electrical length, and protect both coaxial interfaces from moisture and strain.
NSv scale, linear range and frequency response belong to the matched system. Commissioning must also verify target size, probe spacing, restored gap or bias and the operating response accepted for the machine.
-
Bently Nevada 330901-00-12-10-02-00 technical reference
Apter Power reference with verified manufacturer data and exact-model applicability. -
Bently Nevada 330901-00-12-10-02-00 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Radial shaft vibration
Use a documented bearing location and matched transducer chain to measure shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the full expected travel inside the characterized working region. -
Phase or speed reference
Use only with an approved once-per-turn target feature and a monitoring channel configured for phase or speed reference. -
Installed-channel maintenance
Preserve the exact probe, cable, Proximitor, mounting geometry and machine baseline recorded for the existing channel.
Match every field of 330901-00-12-10-02-00 with the installed spare-parts record before removal or installation.
Keep the probe tip, connector and cable free from impact, moisture, metal chips and unsupported loading.
Record reach, thread engagement, lock position and target relationship before disturbing the installed component.
Maintain the approved bend radius, separation and strain relief; do not twist, kink or crush the coaxial path.
Use the approved stopped-machine procedure to restore gap or bias and verify expected target travel.
Verify the as-left electrical reading, monitor indication and operating response before return to service.
Alternative Names
Technical notes
Installation relationship: The 1/4-28 UNF-2A mounting, 0.0 in reach and 1.2 in case define the mechanical position.
Small-target boundary: Verify target size, side-view clearance and adjacent-probe spacing before setting the operating gap.
Technical reference: Bently Nevada 3300 XL NSv Proximity Transducer System Datasheet, 147385 Rev. R.
FAQ View All FAQ
-
Which companion components are required for 330901-00-12-10-02-00?Use 330901-00-12-10-02-00 with the documented NSv extension cable and NSv Proximitor whose total system length matches the installed channel.
-
How should small-target effects be reviewed for 330901-00-12-10-02-00?Check shaft diameter, flat-target size, side-view clearance and nearby conductive surfaces; small targets can change scale factor and require a documented application review.
-
How should cross-talk be assessed around 330901-00-12-10-02-00?Confirm probe-tip separation and target geometry, then observe adjacent channels during a controlled target movement before accepting the installation.
-
What proves the operating gap of 330901-00-12-10-02-00 is acceptable?Use the approved stopped-machine method to restore the documented 1.0 mm reference gap or accepted bias, then verify the full expected target travel remains inside the characterized region.
-
What evidence should be captured before removing 330901-00-12-10-02-00?Photograph the complete 330901-00-12-10-02-00 marking, installed datum, connector, cable route and companion electronics. Record the stopped-machine baseline for the 3300 XL NSv proximity probe.
-
How should connector integrity be checked on 330901-00-12-10-02-00?Isolate the channel, inspect the coaxial contacts for moisture and damage, verify continuity only with an approved method, and provide strain relief so the connector carries no cable load.
-
What commissioning record is required for 330901-00-12-10-02-00?Retain the exact markings, mechanical datum, companion-component identities, as-left gap or bias, monitor indication and the accepted operating response.
-
When should 330901-00-12-10-02-00 be withheld from service?Do not release the channel if the complete identity, mechanical fit, cable construction, connector, approval marking or measured response differs from the approved installed record.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330901-00-12-10-02-00Product Details -
330104-00-04-10-02-05Product Details -
330105-02-12-10-02-05Product Details -
330104-00-18-10-02-00Product Details -
330104-00-22-10-02-00Product Details -
330103-00-16-10-02-05Product Details -
330103-00-08-05-02-CNProduct Details -
330104-00-06-10-02-00Product Details -
330104-00-06-10-11-00Product Details -
330101-00-81-10-02-05Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







