Which thread and body length are specified for TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10?

This configuration uses an M10 × 1 thread under B1 and a 42 mm body length under C42.

How much unthreaded length is present on TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10?

Option D2 defines a 2 mm unthreaded section on the ordered sensor body.

What integral cable is documented for TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10?

Option E10000 supplies a 10000 mm FEP-covered 70 Ω coaxial cable with a published ±1000 mm tolerance.

Which protective construction accompanies TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10?

Option F2 identifies a flexible stainless-steel hose with an FEP sheath and no IP172 connector protector.

What temperature range applies to the TQ902-011 sensor?

The TQ902-011 sensor is specified for operation from −40 to +180 °C, while its head and integral cable assembly carries an IP68 rating.

Which measurement ranges can a TQ902-011 chain support?

A matched TQ902-011 and IQS900 chain supports a 2 mm or 4 mm linear range according to the conditioner configuration.

How should TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 be accepted after installation?

Technicians should verify the complete identity, mechanical gap, cable and connector condition, matched conditioner configuration, diagnostics and every affected machinery-monitoring function.

TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10

Name: TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10
Brand: Vibro-Meter
SKU: TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10

Proximity Sensor

Vibro-Meter TQ902-011-111-902-000-011-A1-B1-C42-D2-E10000-F2-G9800-H10 (1)

Vibro-Meter TQ902-011-111-902-000-011-A1-B1-C42-D2-E10000-F2-G9800-H10 (2)

Vibro-Meter TQ902-011-111-902-000-011-A1-B1-C42-D2-E10000-F2-G9800-H10 (3)

Product image is representative; revision or series may vary. Contact us to request a specific version.

Product Describe：

Vibro-Meter TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 is a standard-mount proximity sensor for a TQ9xx/IQS900 measurement chain. Its confirmed complete identifier is retained exactly, while only option meanings supported by the manufacturer’s published tables are stated as technical values.

Ask our team:

Phone: +86 180 3023 5313 E-Mail: sales13@apterpower.com

Dispatch Planning
Confirm stock and lead time with our team.

Dedicated Manager
Personalized one-to-one VIP service

ISO 9001:2015 Certified
Trusted quality management

Get a quick price for TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10

E-mail *

Mobile *

Company

Content *

Quantity *

Upload (gif, jpg, jpeg, png, bmp, doc, docx, xls, xlsx, ppt, pdf, csv)

Get a Quote

For more information on how your data is processed and stored by Apterpower please read our privacy policy

What happens after you enquire

1

Requirement review

We review the part number, quantity and delivery requirements and ask for any missing details.
2

Quotation and availability

We confirm the proposed item, condition, availability, price and estimated lead time in the quotation.
3

Order confirmation and dispatch

Once the quotation and purchasing details are agreed, your contact will coordinate the order and available dispatch information.

Technical specifications for TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10

Manufacturer:

Vibro-Meter
Product Category:

General Automation
Spare Part Number:

TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10
Estimated shipping dimensions:

22x26x2cm
Weight:

0.15 kg
Tariff Code:

8537101190
Counliy of origin:

Switzerland
Product line:

Vibro-Meter TQ902 standard-mount proximity sensor
Measurement principle:

Non-contact eddy-current displacement sensing
Environment option A1:

Standard environment
Body thread option B1:

M10 × 1
Body length option C42:

42 mm
Unthreaded length option D2:

2 mm
Integral cable option E10000:

10000 mm ±1000 mm
Protection option F2:

Flexible stainless-steel hose with FEP sheath; no IP172 connector
Total system length option H10:

10 m
Supported linear measurement ranges:

2 mm or 4 mm with the configured IQS900
Frequency response:

DC to 20 kHz (−3 dB)
Sensor operating temperature:

−40 to +180 °C
Sensor head protection:

IP68 according to IEC 60529
Sensor construction:

PPS tip and AISI 316L stainless-steel body
Integral cable:

FEP-covered 70 Ω coaxial cable, 3.6 mm diameter
Connector:

Self-locking miniature coaxial cable plug

View as PDF Ask for Quote

Information

Overview Manuals Common Applications Product Precautions

Installed at the machine, this TQ902-011 configuration senses the changing gap to a metallic target and passes the response through its integral coaxial cable to the matched conditioning chain.

Standard-mount TQ902 sensor architecture
M10 × 1 body with 42 mm body length
10 m integral FEP coaxial cable
Flexible stainless-steel hose with FEP sheath

The sensor tip contains an eddy-current coil within a PPS high-temperature thermoplastic tip crimped to an AISI 316L stainless-steel body. When paired with an IQS900 and the documented cabling, the TQ902 chain supports relative-vibration and axial-position measurements with a DC to 20 kHz response. Maintain the complete supplied marking exactly and use the installed manufacturer record when reconciling cable-protection details, total-system length and replacement hardware.

Important Notice: Confirm the complete TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 marking and the installed manufacturer configuration record before replacement.

Vibro-Meter TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 Manuals & Downloads

Vibro-Meter TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 Official Technical Reference Excerpt (PDF)Vibro-Meter TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 Installation & Commissioning Guide (PDF)

The first document contains the applicable manufacturer reference pages; the second organizes preparation, mounting, cable handling, diagnostics and handover checks.

Turbine shaft monitoring

Measures documented radial shaft displacement or axial position without contacting the rotating target.

Compressor protection

Supplies the sensor-side signal for approved machinery-protection and condition-monitoring channels.

Pump and alternator supervision

Tracks metallic-shaft gap changes in calibrated TQ902/IQS900 measurement chains.

High-temperature sensor locations

Supports installed sensor points whose operating conditions remain within the published −40 to +180 °C range.

Read the applicable Vibro-Meter instructions before work. Verify TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 and the installed system configuration before isolation or replacement.

Record the entire TQ902-011 order and option string exactly as supplied.

Place the machine and affected monitoring or protection functions in the approved maintenance state.

Verify the M10 × 1 thread, 42 mm body and 2 mm unthreaded section before mounting.

Protect the PPS sensor tip and set the initial gap using the approved target and procedure.

Route the integral cable and FEP-sheathed flexible protection without sharp bends or tensile loading.

Keep the self-locking miniature coaxial connector clean, dry and electrically insulated.

Reconcile the complete G9800 marking and H10 chain record with the installed manufacturer documentation.

Prove gap output, vibration response, diagnostics and every affected protection channel before release.

Technical notes

This page preserves G9800 as part of the user-confirmed complete product identity but does not assign it an unsupported dimensional value. Verified installation data include the M10 × 1 body, 42 mm body length, 2 mm unthreaded length, 10 m integral cable, F2 protection and H10 total-system code.

FAQ View All FAQ

Where does Vibro-Meter TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 fit in a measurement chain?

The TQ902-011 sensor forms the standard-mount front end of a calibrated TQ9xx proximity chain used with compatible cabling and an IQS900 signal conditioner.
Which thread and body length are specified for TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10?

This configuration uses an M10 × 1 thread under B1 and a 42 mm body length under C42.
How much unthreaded length is present on TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10?

Option D2 defines a 2 mm unthreaded section on the ordered sensor body.
What integral cable is documented for TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10?

Option E10000 supplies a 10000 mm FEP-covered 70 Ω coaxial cable with a published ±1000 mm tolerance.

Which protective construction accompanies TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10?

Option F2 identifies a flexible stainless-steel hose with an FEP sheath and no IP172 connector protector.
What temperature range applies to the TQ902-011 sensor?

The TQ902-011 sensor is specified for operation from −40 to +180 °C, while its head and integral cable assembly carries an IP68 rating.
Which measurement ranges can a TQ902-011 chain support?

A matched TQ902-011 and IQS900 chain supports a 2 mm or 4 mm linear range according to the conditioner configuration.
How should TQ902-011 111-902-000-011 A1-B1-C42-D2-E10000-F2-G9800-H10 be accepted after installation?

Technicians should verify the complete identity, mechanical gap, cable and connector condition, matched conditioner configuration, diagnostics and every affected machinery-monitoring function.

Manufacturers

Supporting new and legacy automation

Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.

Please try to be as accurate as possible with your search.
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
We can't find any results for “”.