Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for NJ15-30GK50-E2-30M
For more information on how your data is processed and stored by Apterpower please read our privacy policy
Technical specifications for NJ15-30GK50-E2-30M
-
Manufacturer:Pepperl+Fuchs
-
Product Category:General Automation
-
Spare Part Number:NJ15-30GK50-E2-30M
-
Estimated shipping dimensions:17x16x1cm
-
Weight:0.05 kg
-
Tariff Code:8537101190
-
Counliy of origin:Germany
-
Sensor type:Inductive proximity sensor
-
Output function:PNP, normally open
-
Wiring:Three-wire
-
Nominal sensing distance:15 mm
-
Assured operating range:0–12.15 mm
-
Mounting:Non-flush
-
Operating voltage:10–60 V DC
-
Switching frequency:0–500 Hz
-
Operating current:0–200 mA
-
No-load current:9 mA maximum
-
Readiness delay:50 ms maximum
-
Cable:30 m PVC, 0.75 mm² conductors
-
Housing and sensing face:PBT
-
Degree of protection:IP68
-
Ambient temperature:-25 to 70 °C
Information
Overview
Manuals
Common Applications
Product Precautions
The NJ15-30GK50-E2-30M detects a suitable metal target without contact and switches a PNP normally-open output within its assured operating range.
- 15 mm nominal sensing distance
- PNP normally-open three-wire output
- 10–60 V DC operating voltage
- Integral 30 m PVC cable
This non-flush PBT-bodied sensor provides an assured operating distance of 0–12.15 mm and supports switching frequencies up to 500 Hz. The output is protected against reverse polarity and pulsing short circuit, while the 30 m cable uses 0.75 mm² conductors. Installation must preserve the documented target geometry, non-flush mounting and cable identification.
Important Notice: Verify the complete NJ15-30GK50-E2-30M suffix, target material, non-flush mounting, supply polarity and 30 m cable route before replacement.
Pepperl+Fuchs NJ15-30GK50-E2-30M Manuals & Downloads
Pepperl+Fuchs NJ15-30GK50-E2-30M Official Manufacturer Manual (PDF)Pepperl+Fuchs NJ15-30GK50-E2-30M Installation & Commissioning Guide (PDF)
The first document reproduces applicable official manufacturer pages unchanged; the second provides a separate evidence-led installation and commissioning workflow.
Position detection
Non-contact detection of a suitable metal target in documented machinery and automation positions.
End-position feedback
PNP normally-open feedback for mechanisms whose target and non-flush mounting match the approved design.
Long cable runs
Installations requiring the exact integral 30 m PVC cable supplied with this sensor variant.
Washdown-protected areas
IP68 sensing points operated within the published temperature, voltage and environmental limits.
Read the applicable Pepperl+Fuchs instructions before work. Verify NJ15-30GK50-E2-30M and the installed system configuration before isolation or replacement.
1
Record the complete NJ15-30GK50-E2-30M marking and installed target position.
2
Isolate the 10–60 V DC circuit and prove the conductors safe before work.
3
Verify PNP normally-open logic against the controller input before connection.
4
Preserve non-flush mounting and the approved metal target geometry.
5
Protect the integral 30 m PVC cable from cuts, crushing and excessive bend stress.
6
Check polarity, load current and short-circuit conditions before energization.
7
Set the operating distance within the assured 0–12.15 mm range.
8
Cycle the target and record stable switching and final acceptance results.
Technical notes
This non-flush PBT-bodied sensor provides an assured operating distance of 0–12.15 mm and supports switching frequencies up to 500 Hz. The output is protected against reverse polarity and pulsing short circuit, while the 30 m cable uses 0.75 mm² conductors. Installation must preserve the documented target geometry, non-flush mounting and cable identification.
FAQ View All FAQ
-
What type of device is NJ15-30GK50-E2-30M?The NJ15-30GK50-E2-30M is a non-flush inductive proximity sensor with a PNP normally-open output.
-
How far can the Pepperl+Fuchs sensor detect its target?The Pepperl+Fuchs sensor has a 15 mm nominal sensing distance and a 0–12.15 mm assured operating range.
-
Which supply voltage does NJ15-30GK50-E2-30M require?The NJ15-30GK50-E2-30M requires a 10–60 V DC operating supply.
-
What switching frequency is specified for this NJ15 sensor?This NJ15 sensor supports a switching frequency from 0 to 500 Hz.
-
How is the output of NJ15-30GK50-E2-30M protected?The output of NJ15-30GK50-E2-30M includes reverse-polarity protection and pulsing short-circuit protection.
-
Which cable is supplied with the E2-30M variant?The E2-30M variant is supplied with an integral 30 m PVC cable using 0.75 mm² conductors.
-
What environmental limits apply to NJ15-30GK50-E2-30M?The NJ15-30GK50-E2-30M is rated IP68 and operates from -25 to 70 °C.
-
What must be checked after installing the Pepperl+Fuchs proximity sensor?The technician must cycle the approved target and verify stable PNP switching at the documented operating distance after installation.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Related reading
Related cases and sourcing guidance
View all case studies
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.