-
Match the complete marking
Include FSP400-60PFI and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation.
-
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered FSP400-60PFI reference with the installed equipment and applicable FSP documentation.
Technical specifications for FSP400-60PFI
-
Manufacturer:FSP
-
Product Category:General Automation
-
Spare Part Number:FSP400-60PFI
-
Weight:2.02 kg
-
Tariff Code:8537101190
-
Rated output power:400 W
-
AC input range:100 to 240 V AC
-
Input frequency:50/60 Hz
-
Maximum marked input current:6.3 A
-
DC rail set:+3.3 V, +5 V, +12 V, -12 V and +5 V standby
-
12 V architecture:Separate +12 V1 and +12 V2 rails are identified in cross-checked records
-
Power-good signal:P.G. signal lead identified in cross-checked wiring records
-
Protective conductor:Ground return conductors form part of the installed harness
-
Replacement rule:Match every connector position and rail assignment to the removed supply
-
Evidence boundary:Individual rail-current values are not published here because available records conflict
Information
- The complete FSP400-60PFI identity establishes the offered hardware. Confirm the installed system, revision and field interfaces before approving the replacement.
Replacement boundary: Rated wattage alone does not prove connector or rail compatibility.
Installation focus: Preserve harness position, chassis airflow and protective-earth continuity.
A correct changeover requires connector-by-connector comparison, not only a 400 W match. Record the original plug positions, wire colours, standby rail, power-good lead and protective-earth path before removal.
Commissioning should verify standby behaviour, controlled start-up, each populated rail under load, fan direction and chassis temperature. If the delivered label differs from the recorded unit, hold the replacement for review.
-
FSP FSP400-60PFI technical reference
Apter Power reference with verified manufacturer data and exact-model applicability. -
FSP FSP400-60PFI engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
Industrial computer service
Restore the exact multi-rail supply arrangement in a documented computer chassis. -
Control-system workstation maintenance
Replace a failed supply while preserving motherboard and storage power connections. -
Legacy equipment refurbishment
Use the complete label and connector map to support a controlled like-for-like change. -
Bench acceptance
Prove rail presence, standby operation and power-good behaviour with an approved load method.
Photograph and label the full harness before removing any plug.
Isolate AC power and follow the approved wait and voltage-verification procedure.
Confirm protective-earth continuity between supply and chassis before energizing.
Keep the fan path, inlet and exhaust clear and confirm the installed orientation.
Verify the standby rail and control signal before permitting full system start-up.
Record populated-rail voltage and system stability under the approved operating load.
Alternative Names
Technical notes
Installation relationship: Use the exact model marking and manufacturer wiring or installation information for the delivered hardware.
System boundary: Verify host equipment, companion interfaces, field wiring and configuration before energizing.
Technical reference: cross-checked FSP400-60PFI nameplate data from multiple established industrial-parts records.
FAQ View All FAQ
-
How should the connector map of FSP400-60PFI be captured before removal?Photograph every plug from two angles, label its chassis destination, and record keying, latch direction, wire colours and unused positions before disconnecting the harness.
-
Which live checks are most useful when diagnosing FSP400-60PFI?Use the approved electrical-safety method to verify AC input, standby output, start command, populated DC rails and power-good state under the installed load.
-
How can an intermittent shutdown involving FSP400-60PFI be separated from a downstream fault?Correlate each rail with load current and temperature, then isolate approved loads systematically. Do not condemn the supply from an unloaded voltage check alone.
-
What must be verified before fitting a substitute for FSP400-60PFI?Compare the complete label, mechanical envelope, fan direction, connector count, keying, pin assignments, standby rail and power-good behaviour.
-
How should protective-earth integrity be proved for FSP400-60PFI?With power isolated, inspect the earth conductor and mounting points, then measure continuity using the site-approved method and record the result before energizing.
-
What thermal evidence should be recorded after installing FSP400-60PFI?Record inlet and exhaust condition, fan operation and stabilized chassis temperature while the computer runs its representative workload.
-
Why are individual rail-current values not assigned to FSP400-60PFI on this page?Available independent records disagree on several rail currents. Use the supplied nameplate and installed-system documentation as the controlling source.
-
What constitutes an acceptable as-left record for FSP400-60PFI?Retain label photographs, connector map, earth-continuity result, standby and loaded rail measurements, power-good behaviour and final operating observation.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
FSP400-60PFIProduct Details -
KPCI-PIO32IOAProduct Details -
KFD2-SOT3-EX1.LBProduct Details -
EVS9324-EPProduct Details -
M-FAST SFP-MM/LCProduct Details -
M00279-3266-140Product Details -
G128-0001Product Details -
SYS68K-CPU-30BE16-REV-3Product Details -
PR6423/018-140 CON021Product Details -
PR6424/014-140 CON021Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






