-
Match the complete marking
Include KJ3221X1-BA1 12P2531X102 VE4035S2B1 and any revision or assembly number visible on the item. Keep the exact reference on your enquiry and quotation.
-
Check the offered item before ordering
Request available label and connection photos. Have your maintenance team compare the offered KJ3221X1-BA1 12P2531X102 VE4035S2B1 with the installed equipment and applicable manufacturer documentation.
Technical specifications for KJ3221X1-BA1 12P2531X102 VE4035S2B1
-
Manufacturer:Emerson
-
Product Category:DCS Systems
-
Spare Part Number:KJ3221X1-BA1 12P2531X102 VE4035S2B1
-
Weight:0.18 kg
-
Tariff Code:8537101190
-
Card family:DeltaV M-series Traditional I/O
-
Physical card marking:KJ3221X1-BA1
-
Part number:12P2531X102
-
Catalog assembly reference:VE4035S2B1
-
Catalog I/O role:8-channel 4–20 mA HART output assembly
-
Termination arrangement:Redundant standard I/O termination block
-
Analog loop:4–20 mA with HART
-
Catalog point count:8 channels
-
Catalog pairing:Redundant analog output arrangement
-
Full output range:1–23 mA
-
Output resolution:12-bit
-
Accuracy over temperature:0.25% of span
-
Channel isolation:Optical; 1500 V DC factory test
-
Output compliance:20 mA into 700 Ω at 21.6 V DC supply
-
LocalBus current:100 mA typical; 150 mA maximum at 12 V DC
Information
- The DeltaV redundant HART analog output assembly serves the configured DeltaV I/O node and its matched field termination arrangement.
Commissioning: Verify point mapping and affected alarms
Selection: Match the card, termination and host release
The 8-channel catalog arrangement uses the redundant standard I/O termination block. The analog output channels send configured 4–20 mA commands and support HART communication with suitable field devices. Wiring and host assignments are governed by the installed project.
Before replacement, preserve the 4–20 mA HART channel map, terminal wiring, host release and any redundant pairing. Compare the complete KJ3221X1-BA1 12P2531X102 VE4035S2B1 marking with the offered unit and confirm the included termination hardware in the quotation. Commission each affected channel against its approved loop or I/O test.
-
Emerson KJ3221X1-BA1 12P2531X102 VE4035S2B1 technical reference
Apter Power technical reference - PDF, 2 pages. Verified product identity, system role, configuration boundaries and engineering checks. -
Emerson KJ3221X1-BA1 12P2531X102 VE4035S2B1 installation guide
Prepared by Apter Power - PDF, 1 page. Identification, installation preparation, configuration and acceptance checks.
Compatibility scope: Match the physical card and the documented assembly reference to the host release, carrier, termination and channel configuration.
DeltaV output
Deliver proportional field-device commands from the configured control strategy.Field interface
The redundant standard i/o termination block must match the installed wiring and carrier.Redundant output pair
Use the redundant catalog arrangement only where output switchover and the matched terminal block are configured in the host project.System restoration
Return the affected channels to service only after the approved loop, I/O and diagnostic checks pass.
Compare KJ3221X1-BA1 12P2531X102 VE4035S2B1 with the installed label, part number and any revision.
Record the existing channel assignment, host release and termination arrangement.
Check the 4–20 mA HART wiring and the approved circuit drawing before transfer.
Place affected loops in their approved safe state and isolate power as required.
Use the site electrostatic-discharge and connector handling procedure.
Verify recognition, channel behavior and diagnostics against the pre-service record.
Alternative Names
Technical notes
Technical basis: Emerson DeltaV M-series Traditional I/O Product Data Sheet, September 2023.
Applicability: VE4035S2B1 catalog characteristics describe the documented assembly. Confirm applicability of those characteristics to the complete KJ3221X1-BA1 12P2531X102 VE4035S2B1 physical marking and installed termination arrangement.
Commissioning evidence: Compare pre-service and post-service I/O or controller diagnostics, record the affected points, and retain the signed site acceptance result for KJ3221X1-BA1 12P2531X102 VE4035S2B1.
FAQ View All FAQ
-
How should the installed 4–20 mA HART channel map be preserved when replacing KJ3221X1-BA1 12P2531X102 VE4035S2B1?Export or record each configured point and termination assignment, then compare the restored mapping with the project and loop drawings.
-
What could cause a healthy output card to remain offline after fitting KJ3221X1-BA1 12P2531X102 VE4035S2B1?Check host compatibility, carrier connection, power, module recognition and the control-system diagnostic record before attributing the fault to the card.
-
How should field wiring be checked before commissioning KJ3221X1-BA1 12P2531X102 VE4035S2B1?Compare conductor identification, polarity or commons, shielding and terminal assignment with the approved installation drawing.
-
Can KJ3221X1-BA1 12P2531X102 VE4035S2B1 be exchanged with a visually similar DeltaV card?Physical fit is insufficient. Match the complete order marking, card role, termination hardware, host release and project configuration.
-
Which records help diagnose a changed reading or command after fitting KJ3221X1-BA1 12P2531X102 VE4035S2B1?Compare commanded output, measured loop current, HART status and field-device travel under the approved loop test.
-
How should redundancy be reviewed for KJ3221X1-BA1 12P2531X102 VE4035S2B1?Check whether the actual installed assembly is configured as a redundant pair and test the approved failover path; a redundant catalog reference alone is insufficient.
-
What acceptance test is appropriate after installing KJ3221X1-BA1 12P2531X102 VE4035S2B1?Exercise or simulate affected points under the site procedure and verify expected controller indication, field response and alarms.
-
What should be included in the engineering handover for KJ3221X1-BA1 12P2531X102 VE4035S2B1?Record the full physical marking, revision, installed position, terminal assignment, changed configuration and post-service test results.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
KJ3221X1-BA1 12P2531X102 VE4035S2B1Product Details -
KJ3243X1-BK1 SE4022 12P4691X042Product Details -
KJ3002X1-BA1 12P0680X072 VE4003S2B2Product Details -
KJ3221X1-BA1 12P2531X102Product Details -
KJ1501X1-BC1 12P2186X032 VE5008Product Details -
KJ3201X1-BA1 12P2535X052Product Details -
KJ2002X1-BA1 12P1442X042 VE3002Product Details -
PR6424/013-140 CON021/914-100Product Details -
PHARPSPEP11013Product Details -
40CN3210BProduct Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.





