-
Match the complete marking
Include 330707-00-25-10-12-00 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 330707-00-25-10-12-00 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330707-00-25-10-12-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330707-00-25-10-12-00
-
Weight:0.1 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 11 mm
-
Mounting thread:5/8-18 UNF-2A
-
Cable armor:No armor
-
Unthreaded length:0.0 in
-
Overall case length:2.5 in
-
Total probe length:1.0 m
-
Connector:Miniature coaxial ClickLoc, FluidLoc cable
-
Approval selection:No agency approval
-
Nominal probe resistance:5.9 +/- 0.5 ohm
-
Matched-system linear range:4.0 mm (160 mil)
-
Matched-system scale factor:3.94 V/mm (100 mV/mil)
-
Recommended gap:2.5 mm (100 mil)
-
Matched-system frequency response:0 to 8 kHz, +0/-3 dB typical
-
Probe cable impedance:75 ohm triaxial
-
Reference target:AISI 4140 steel, 31 mm diameter or larger
-
Minimum bend radius:25.4 mm
-
Probe temperature:-52 to +177 deg C operating and storage
Information
- Bently Nevada 330707-00-25-10-12-00 is a 5/8-18 UNF-2A unarmored 3300 XL 11 mm probe for long-range non-contact displacement and vibration measurement in a matched 11 mm chain.
Lead interface: 1.0 m; Miniature coaxial ClickLoc, FluidLoc cable.
Long-range role: 4.0 mm matched-system range for displacement, vibration and phase-reference duties.
The 1.0 m lead terminates in miniature coaxial clickloc, fluidloc cable. Preserve the 5 m or 9 m electrical-chain selection, keep the gold-plated ClickLoc interface clean and dry, and support the lead independently.
The 4.0 mm range and 3.94 V/mm scale factor belong to a complete probe, extension cable and Proximitor system on the reference target. Acceptance restores the documented 2.5 mm gap or bias and proves the monitor response.
-
Bently Nevada 330707-00-25-10-12-00 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 330707-00-25-10-12-00 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below require the documented 3300 XL 11 mm proximity transducer system companion components and approved machine drawing.
-
Radial shaft vibration
Use the complete matched transducer chain at a documented bearing location to observe shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the expected travel inside the characterized linear region. -
Phase reference
Use only where the installed target feature and monitoring channel are approved for once-per-turn phase reference. -
Installed-channel maintenance
Preserve the recorded probe, extension cable, Proximitor, target material, mounting geometry and monitor assignment.
Match every field of 330707-00-25-10-12-00 with the installed spare-parts and channel records.
Prevent impact, metal-particle contact and contamination at the probe tip during handling.
Record thread engagement, reach, lock position, target relationship and as-found gap or bias before removal.
Maintain the approved bend radius, connector protection and independent strain relief; do not twist the probe lead.
Use the approved stopped-machine procedure to restore the documented gap or bias.
Verify as-left electrical indication and controlled machine response against the accepted baseline.
Alternative Names
Technical notes
Mechanical relationship: The 5/8-18 UNF-2A mounting, 0.0 in reach and 2.5 in case define probe position and thread engagement.
Electrical relationship: Use the 1.0 m lead only inside the documented 3300 XL 11 mm 5 m or 9 m chain.
Technical reference: Bently Nevada 3300 XL 11 mm Proximity Transducer System Datasheet, 146256 Rev. T.
FAQ View All FAQ
-
How should the installed port be checked before fitting 330707-00-25-10-12-00?Compare the 5/8-18 UNF-2A mounting, 0.0 in unthreaded reach and 2.5 in case with the machine drawing, record the as-found datum and verify that expected target travel will remain clear before the old probe is moved.
-
Which companion electronics must be retained with 330707-00-25-10-12-00?Keep 330707-00-25-10-12-00 inside the documented 3300 XL 11 mm proximity transducer system; confirm the extension-cable and Proximitor identities and the selected total system length.
-
What connector inspection is required for 330707-00-25-10-12-00?The selected interface is Miniature coaxial ClickLoc, FluidLoc cable. Isolate the channel, inspect mating surfaces for moisture, contamination and damage, then seat and support the connection without lead strain.
-
How is the operating point restored after installing 330707-00-25-10-12-00?Use the approved stopped-machine method to restore the recorded gap or bias, then perform a 2.5 mm gap or accepted bias and monitor-response comparison against the machine baseline.
-
How should target material be handled when accepting 330707-00-25-10-12-00?Use the documented target material and geometry for the installed machine; a different alloy, curvature or target area can change scale and linearity.
-
What check helps separate a probe fault from a monitor fault on 330707-00-25-10-12-00?Compare the stopped-machine gap or bias at the Proximitor with the local monitor indication, then inspect the probe and cable path before substituting electronics.
-
When must 330707-00-25-10-12-00 be withheld from service?Do not release the channel if identity, mounting geometry, connector, companion electronics, target relationship or controlled response differs from the approved record.
-
What as-left evidence should be retained for 330707-00-25-10-12-00?Retain the full marking, mechanical datum, companion identities, as-left gap or bias, monitor indication and controlled operating response.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330707-00-25-10-12-00Product Details -
330103-02-04-10-02-05Product Details -
330103-00-05-10-02-INProduct Details -
330905-00-25-05-01-05Product Details -
330901-00-90-10-01-05Product Details -
128987-130-00-00Product Details -
330930-060-01-05Product Details -
330930-065-01-00Product Details -
330500-04-01Product Details -
2098-DSD-010XProduct Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







