How should engineers confirm the system length for 330130-080-12-05?

Add the installed probe lead and extension-cable lengths, then compare the total with the matching Proximitor Sensor length before energizing the channel.

What connector checks are required for 330130-080-12-05?

Inspect both mating surfaces for contamination or damage, align the ClickLoc connector correctly and tighten it finger-tight until the locking action is complete.

How should 330130-080-12-05 be routed in a machinery enclosure?

Maintain the documented bend radius, provide mechanical support and keep the cable away from sharp edges, hot surfaces and locations that can impose tensile load.

What must be recorded before replacing 330130-080-12-05?

Record the full catalog marking, mounting position, companion component numbers, cable route, monitor channel, static gap and as-found polarity.

How is the channel recommissioned after installing 330130-080-12-05?

Restore the matched loop, verify supply and bias voltage, prove movement through the expected linear region and test the configured alarm or trip response under controlled conditions.

Can 330130-080-12-05 be mixed with another probe family?

Use only combinations explicitly permitted by the 3300 XL 8 mm Proximity Transducer System documentation; connector fit alone does not establish electrical calibration or interchangeability.

What maintenance condition should trigger inspection of 330130-080-12-05?

Inspect the assembly after cable impact, connector contamination, abnormal bias voltage, unstable vibration, loss of linear response or any work that changes the probe mounting.

Which Bently Nevada transducer system uses 330130-080-12-05?

330130-080-12-05 belongs to the 3300 XL 8 mm Proximity Transducer System and must be combined only with the probe, extension cable and Proximitor Sensor arrangement documented for that system.

Bently Nevada 330130-080-12-05 3300 XL 8 mm FluidLoc extension cable with connector protector

Name: 330130-080-12-05
Brand: Bently Nevada
SKU: 330130-080-12-05

330130-080-12-05

3300 XL 8 mm FluidLoc extension cable with connector protector

In Stock

Ships by Tuesday, September 22

Fast Shipping Available

Technical specifications for 330130-080-12-05

Manufacturer:

Bently Nevada

Product Category:

Machinery Monitoring System

Spare Part Number:

330130-080-12-05

Estimated shipping dimensions:

20x20x2cm

Weight:

2.28 kg

Tariff Code:

8537101190

Counliy of origin:

USA

Cable length:

8.0 m (26.2 ft)

Cable type:

FluidLoc

Connector protection:

Connector protector

Agency approval option:

Multiple approvals

Cable impedance:

75 ohm triaxial

Cable insulation:

FEP

Core resistance:

1.76 +/- 0.26 ohm

Jacket resistance:

0.53 +/- 0.11 ohm

Capacitance:

69.9 pF/m typical

Minimum bend radius:

25.4 mm (1.0 in)

Information

Overview Manuals Common Applications Product Precautions

Bently Nevada 330130-080-12-05 is 3300 xl 8 mm fluidloc extension cable with connector protector. It extends a 3300 XL 8 mm eddy-current proximity loop while limiting fluid migration through the cable interior.

Provides eight metres of extension length
Uses FluidLoc cable construction
Includes probe-side connector protection
Supports a matched 3300 XL 8 mm system with multiple approvals

330130-080-12-05 is installed with 3300 XL 8 mm probe, matched 3300 XL Proximitor Sensor, ClickLoc coaxial connectors, compatible vibration or position monitor.

Engineered applications include Oil-film bearing vibration monitoring, Axial thrust-position loops, Keyphasor phase-reference service, Turbomachinery proximity-loop replacement.

Important Notice: Verify the required total system length before connecting 330130-080-12-05, keep the protected ClickLoc joint free of oil and contamination, and route the FluidLoc cable without crushing, kinking or tensile load.

Apter Power 330130-080-12-05 Manuals and Guides

Apter Power 330130-080-12-05 Product Technical Reference PDF 330130-080-12-05 Engineering Installation and Verification Workbook

The first document presents model-specific technical identity and engineering data. The second provides a separate installation, connection and commissioning workflow.

Oil-film bearing vibration monitoring

330130-080-12-05 supports this documented 3300 XL 8 mm Proximity Transducer System engineering task.

Axial thrust-position loops

330130-080-12-05 supports this documented 3300 XL 8 mm Proximity Transducer System engineering task.

Keyphasor phase-reference service

330130-080-12-05 supports this documented 3300 XL 8 mm Proximity Transducer System engineering task.

Turbomachinery proximity-loop replacement

330130-080-12-05 supports this documented 3300 XL 8 mm Proximity Transducer System engineering task.

Read the applicable Bently Nevada instructions before work. Verify 330130-080-12-05 and the installed-system configuration.

Verify the complete 330130-080-12-05 marking and its documented 3300 XL 8 mm Proximity Transducer System position before field work.

Place the monitored machine and associated protection channel in the approved maintenance state before disconnecting 3300 XL 8 mm FluidLoc extension cable with connector protector.

Protect every exposed connector and cable end from oil, moisture, dirt and impact while 330130-080-12-05 is open.

Record probe, extension-cable and Proximitor Sensor identities so the calibrated system length is preserved.

Route 330130-080-12-05 without sharp bends, crushing, abrasion or tensile loading at either coaxial termination.

Clean and finger-tighten each ClickLoc connection; never transfer connector torque or wiring practice from a different transducer family.

Set the static gap only after mechanical mounting and the complete matched loop have been confirmed.

Verify polarity, dynamic response and alarm action before returning the machinery-protection channel to service.

FAQS

How should engineers confirm the system length for 330130-080-12-05?

Add the installed probe lead and extension-cable lengths, then compare the total with the matching Proximitor Sensor length before energizing the channel.
What connector checks are required for 330130-080-12-05?

Inspect both mating surfaces for contamination or damage, align the ClickLoc connector correctly and tighten it finger-tight until the locking action is complete.
How should 330130-080-12-05 be routed in a machinery enclosure?

Maintain the documented bend radius, provide mechanical support and keep the cable away from sharp edges, hot surfaces and locations that can impose tensile load.
What must be recorded before replacing 330130-080-12-05?

Record the full catalog marking, mounting position, companion component numbers, cable route, monitor channel, static gap and as-found polarity.
How is the channel recommissioned after installing 330130-080-12-05?

Restore the matched loop, verify supply and bias voltage, prove movement through the expected linear region and test the configured alarm or trip response under controlled conditions.
Can 330130-080-12-05 be mixed with another probe family?

Use only combinations explicitly permitted by the 3300 XL 8 mm Proximity Transducer System documentation; connector fit alone does not establish electrical calibration or interchangeability.
What maintenance condition should trigger inspection of 330130-080-12-05?

Inspect the assembly after cable impact, connector contamination, abnormal bias voltage, unstable vibration, loss of linear response or any work that changes the probe mounting.
Which Bently Nevada transducer system uses 330130-080-12-05?

330130-080-12-05 belongs to the 3300 XL 8 mm Proximity Transducer System and must be combined only with the probe, extension cable and Proximitor Sensor arrangement documented for that system.

Individual privacy preferences

We use cookies and similar technologies on our website and process your personal data (e.g. IP address), for example, to personalize content and ads, to integrate media from third-party providers or to analyze traffic on our website. Data processing may also happen as a result of cookies being set. We share this data with third parties that we name in the privacy settings.

The data processing may take place with your consent or on the basis of a legitimate interest, which you can object to in the privacy settings. You have the right not to consent and to change or revoke your consent at a later time. This revocation takes effect immediately but does not affect data already processed. For more information on the use of your data, please visit our privacy policy.

Below you will find an overview of all services used by this website. You can view detailed information about each service and agree to them individually or exercise your right to object.

You are under 14 years old? Then you cannot consent to optional services. Ask your parents or legal guardians to agree to these services with you.

330130-080-12-05

Product Describe：

Ask our team:

Warranty Policy

Return Notice

Shipping Method

Parts Availability

How to order

Technical specifications for 330130-080-12-05

Technical specifications for 330130-080-12-05

Information

Information