Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for 330104-10-20-10-02-00
For more information on how your data is processed and stored by Apterpower please read our privacy policy
-
Match the complete marking
Match the complete Bently Nevada 330104-10-20-10-02-00 marking, hardware execution and connection arrangement to the installed position before approving the order.
-
Check the offered item before ordering
Request clear photographs of the offered 330104-10-20-10-02-00 and ask your maintenance team to compare its markings and interfaces with the installed equipment and applicable Bently Nevada instructions.
Technical specifications for 330104-10-20-10-02-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330104-10-20-10-02-00
-
Weight:0.16 kg
-
Tariff Code:8537101190
-
Sensing principle:Non-contact eddy current
-
Tip diameter:8 mm
-
Mounting thread:M10 x 1
-
Unthreaded section:100 mm
-
Case length:200 mm
-
Integral lead length:1.0 m
-
Lead construction:Armored standard coaxial cable
-
Connector:Miniature coaxial ClickLoc
-
Nominal system sensitivity:7.87 V/mm (200 mV/mil)
-
System linear range:2 mm (80 mils)
-
Standard calibration target:AISI 4140 steel
Information
Overview
Downloads
Applications / Compatibility
Product Precautions
- Bently Nevada 330104-10-20-10-02-00 combines an extended unthreaded section with a metric mounting case for a specifically positioned shaft measurement point.
Measurement role: Non-contact shaft position and vibration
Cable construction: Armored standard coaxial lead
Signal path: Matched probe, cable arrangement and Proximitor
Cable construction: Armored standard coaxial lead
Signal path: Matched probe, cable arrangement and Proximitor
The ordered mechanical arrangement has a 200 mm case with a 100 mm unthreaded section. Compare this geometry with the bracket and target position so that the probe can be secured without forcing its cable or shifting the intended sensing direction.
The 1.0 m integral lead is combined with a compatible extension cable to establish the selected system electrical length. The probe cable length is not the total system length, and a mechanically matching extension does not establish electrical compatibility.
The conditioner output represents both static gap and dynamic target motion. Target material, mounting geometry and receiver configuration must remain within the intended measurement design. Armor protects the routed lead but does not replace proper support or connector protection.
The 1.0 m integral lead is combined with a compatible extension cable to establish the selected system electrical length. The probe cable length is not the total system length, and a mechanically matching extension does not establish electrical compatibility.
The conditioner output represents both static gap and dynamic target motion. Target material, mounting geometry and receiver configuration must remain within the intended measurement design. Armor protects the routed lead but does not replace proper support or connector protection.
Controller platform reference: 3300 XL 8 mm system. Use the applicable installation instructions and approved design.
The original technical excerpt supports 330104-10-20-10-02-00 configuration review. The separate Apter Power field guide organizes practical diagnostic checks. Installation topics include: check the 200 mm case and bracket relationship, identify the 1.0 m lead and matched conditioner, route armor and secure the coaxial connection.
330104-10-20-10-02-00 Original Technical Excerpt
The original technical excerpt supports 330104-10-20-10-02-00 configuration review. The separate Apter Power field guide organizes practical diagnostic checks. PDF · 5 pages.330104-10-20-10-02-00 Installation & Verification Guide
Apter Power engineering guide for the installed signal, power or communication path and controlled acceptance. PDF · 5 pages.
Original manufacturer pages retain their technical context. Use the Apter Power guide with the applicable manufacturer instructions and approved installation design.
System and supply context: 330104-10-20-10-02-00 belongs to the 3300 XL 8 mm system installation described by the technical reference. Connected equipment and accessories must be included explicitly in the configured assembly.
Application scope: The following uses describe supported engineering roles; they do not establish interchangeability with another model or remove application-specific validation.
Application scope: The following uses describe supported engineering roles; they do not establish interchangeability with another model or remove application-specific validation.
Fluid-film bearing monitoring
Measure shaft motion with a compatible proximity channel.Static position measurement
Observe conductive target position within the matched-system range.Reference-pulse sensing
Support a properly configured Keyphasor or speed-reference arrangement.Probe replacement service
Match mounting geometry and electrical length to the installed chain.
Prepare Bently Nevada 330104-10-20-10-02-00 for its configured installation using these checks.
Check the 200 mm case and bracket relationship
Record the probe position, target material, sensing direction and monitor channel before removal. Compare the 200 mm case and 100 mm unthreaded portion with the actual bracket and working space. Preserve the original operating gap and the accepted channel scaling so a mechanical replacement does not silently alter the measurement baseline.
Identify the 1.0 m lead and matched conditioner
Trace the 1.0 m integral lead to its conditioner and identify the complete calibrated arrangement. This probe is used with the selected Proximitor electrical length through the compatible extension cable. Keep the machine protection in its approved maintenance state while the channel is interrupted, and label the coaxial connections before disconnecting them.
Route armor and secure the coaxial connection
Inspect the probe tip, armored lead and connector for damage or contamination before installation. Route the armor with support that does not pull on the probe or coaxial connection. Secure the intended mounting position and protect the connector using the applicable installation method, then verify the gap again after locking the mechanical arrangement.
Verify gap response against the actual target
Use the matched chain and a suitable target to observe output at controlled gap positions within the intended operating region. Compare direction and sensitivity with the system requirements, allowing for target material and the receiving instrument. Keep any dynamic interpretation separate from a static electrical verification.
Prove monitor scaling and protection response
Restore the channel to the intended monitor and confirm scaling, normal gap indication and the configured protection response. Perform alarm or reference-pulse checks only under the approved controlled test method. Remove temporary stimuli and reconcile bypasses before returning the measurement to service, retaining the final probe and conditioner identities.
Keep the technical scope explicit
Probe configuration follows the metric ordering table; stated system performance requires a matched transducer chain and the specified target conditions.
Alternative Names
Bently Nevada 330104-10-20-10-02-00
Technical notes
Configuration baseline: Keep the installed 3300 XL 8 mm system arrangement aligned with the complete 330104-10-20-10-02-00 reference and its assigned system role.
Acceptance boundary: Compare the electrical or communication response with the intended application outcome before releasing maintenance controls.
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System, 141194 Rev. AN. Probe configuration follows the metric ordering table; stated system performance requires a matched transducer chain and the specified target conditions.
FAQ View All FAQ
-
Why does the unthreaded portion of 330104-10-20-10-02-00 matter to the mounting assessment?It changes where the usable thread begins relative to the case and sensing tip. Compare the actual bracket engagement and target clearance with the ordered geometry. Matching the thread diameter alone does not establish a suitable mechanical installation.
-
How should 330104-10-20-10-02-00 be checked after an extension cable is replaced?Verify the new cable family and electrical length against the probe and Proximitor. Then perform a controlled gap-response test. A mechanically mating connector does not prove that the complete chain retains its calibration.
-
Can 330104-10-20-10-02-00 share one Proximitor input with another probe?The specified transducer chain uses one probe with its compatible cable and conditioner. Do not parallel probes onto one input; doing so changes the electrical system and does not provide two valid measurement channels.
-
Why can a nearby shaft shoulder affect 330104-10-20-10-02-00 measurement?The probe responds to conductive material in its sensing field. A shoulder or adjacent metal can alter the response compared with a flat calibration target. Verify the installed geometry over the required shaft movement.
-
What distinguishes a cable-routing fault from target movement at 330104-10-20-10-02-00?Hold the target relationship fixed during a controlled inspection and check whether cable or connector movement changes the output. An output change without target motion directs attention to the electrical or mechanical connection path.
-
How should 330104-10-20-10-02-00 be used for a speed-reference application?Use a compatible conditioner and receiving channel configured for the intended target geometry and pulse interpretation. Verify pulse quality through the expected speed range. The probe order code alone does not define a complete speed-measurement system.
-
Why should the monitor scale be checked after replacing 330104-10-20-10-02-00?The receiving channel must interpret the complete transducer-system output correctly. An unchanged gap voltage does not establish correct engineering-unit scaling or alarm thresholds. Compare the configured sensitivity with the matched system.
-
What makes a bench test of 330104-10-20-10-02-00 representative of the installed channel?Use the intended conditioner, cable arrangement and a suitable target material with controlled movement. Record the test configuration. Testing the probe with an unrelated cable or target can conceal an application mismatch.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Related reading
Related cases and sourcing guidance
View all case studies
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.