Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for 330103-00-16-10-12-CN
For more information on how your data is processed and stored by Apterpower please read our privacy policy
Technical specifications for 330103-00-16-10-12-CN
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330103-00-16-10-12-CN
-
Estimated shipping dimensions:116x1.8x1.8cm
-
Weight:0.1 kg
-
Tariff Code:8537101190
-
Counliy of origin:USA
-
Probe thread:M10 x 1
-
Cable armor:None
-
Unthreaded length:0 mm
-
Overall case length:160 mm
-
Total probe length:1.0 m
-
Cable type:FluidLoc
-
Connector:Miniature coaxial ClickLoc
-
Connector protector:Not included
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 303 or 304 stainless steel
-
Cable impedance:75 ohm triaxial
-
Cable insulation:FEP
-
Minimum cable bend radius:25.4 mm (1.0 in)
-
Maximum probe-to-lead tensile strength:330 N (75 lbf)
-
Maximum lead-to-extension tensile strength:270 N (60 lbf)
-
Connector material:Gold-plated brass or beryllium copper
-
Recommended connector torque:Finger tight
-
Maximum connector torque:0.565 N m (5 in lbf)
-
Standard probe temperature:-52 to +177 degC
Information
Overview
Manuals
Common Applications
Product Precautions
Bently Nevada 330103-00-16-10-12-CN is 3300 xl 8 mm metric fluidloc proximity probe. It is a one-metre M10 x 1 probe that converts shaft clearance changes into an eddy-current signal for a matched 3300 XL 8 mm system.
- Uses a 160 mm threaded case
- Includes a one-metre FluidLoc probe lead
- Installs without external armor
- Measures both static position and dynamic vibration
330103-00-16-10-12-CN is installed with one-metre 3300 XL Proximitor Sensor, M10 x 1 mounting bracket, AISI 4140 steel target, compatible machinery-protection channel.
Engineered applications include Confined radial-bearing installations, Axial thrust-position sensing, Machine shaft centerline trending, Speed and phase-reference measurement.
Important Notice: Verify the complete suffix on the physical marking, provide sufficient 160 mm case clearance, keep the FluidLoc lead above its bend limit, and prove polarity and linear response after setting the static gap.
Apter Power 330103-00-16-10-12-CN Manuals and Guides
Apter Power 330103-00-16-10-12-CN Product Technical Reference PDF330103-00-16-10-12-CN Engineering Installation and Verification WorkbookThe first document presents model-specific technical identity and engineering data. The second provides a separate installation, connection and commissioning workflow.
Confined radial-bearing installations
330103-00-16-10-12-CN supports this documented 3300 XL 8 mm Proximity Transducer System engineering task.
Axial thrust-position sensing
330103-00-16-10-12-CN supports this documented 3300 XL 8 mm Proximity Transducer System engineering task.
Machine shaft centerline trending
330103-00-16-10-12-CN supports this documented 3300 XL 8 mm Proximity Transducer System engineering task.
Speed and phase-reference measurement
330103-00-16-10-12-CN supports this documented 3300 XL 8 mm Proximity Transducer System engineering task.
Read the applicable Bently Nevada instructions before work. Verify 330103-00-16-10-12-CN and the installed-system configuration.
1
Verify the complete 330103-00-16-10-12-CN marking and its documented 3300 XL 8 mm Proximity Transducer System position before field work.
2
Place the monitored machine and associated protection channel in the approved maintenance state before disconnecting 3300 XL 8 mm metric FluidLoc proximity probe.
3
Protect every exposed connector and cable end from oil, moisture, dirt and impact while 330103-00-16-10-12-CN is open.
4
Record probe, extension-cable and Proximitor Sensor identities so the calibrated system length is preserved.
5
Route 330103-00-16-10-12-CN without sharp bends, crushing, abrasion or tensile loading at either coaxial termination.
6
Clean and finger-tighten each ClickLoc connection; never transfer connector torque or wiring practice from a different transducer family.
7
Set the static gap only after mechanical mounting and the complete matched loop have been confirmed.
8
Verify polarity, dynamic response and alarm action before returning the machinery-protection channel to service.
Technical notes
Verify the complete suffix on the physical marking, provide sufficient 160 mm case clearance, keep the FluidLoc lead above its bend limit, and prove polarity and linear response after setting the static gap.
FAQ View All FAQ
-
How should 330103-00-16-10-12-CN be routed in a machinery enclosure?Maintain the documented bend radius, provide mechanical support and keep the cable away from sharp edges, hot surfaces and locations that can impose tensile load.
-
What must be recorded before replacing 330103-00-16-10-12-CN?Record the full catalog marking, mounting position, companion component numbers, cable route, monitor channel, static gap and as-found polarity.
-
How is the channel recommissioned after installing 330103-00-16-10-12-CN?Restore the matched loop, verify supply and bias voltage, prove movement through the expected linear region and test the configured alarm or trip response under controlled conditions.
-
Can 330103-00-16-10-12-CN be mixed with another probe family?Use only combinations explicitly permitted by the 3300 XL 8 mm Proximity Transducer System documentation; connector fit alone does not establish electrical calibration or interchangeability.
-
What maintenance condition should trigger inspection of 330103-00-16-10-12-CN?Inspect the assembly after cable impact, connector contamination, abnormal bias voltage, unstable vibration, loss of linear response or any work that changes the probe mounting.
-
Which Bently Nevada transducer system uses 330103-00-16-10-12-CN?330103-00-16-10-12-CN belongs to the 3300 XL 8 mm Proximity Transducer System and must be combined only with the probe, extension cable and Proximitor Sensor arrangement documented for that system.
-
How should engineers confirm the system length for 330103-00-16-10-12-CN?Add the installed probe lead and extension-cable lengths, then compare the total with the matching Proximitor Sensor length before energizing the channel.
-
What connector checks are required for 330103-00-16-10-12-CN?Inspect both mating surfaces for contamination or damage, align the ClickLoc connector correctly and tighten it finger-tight until the locking action is complete.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.