-
Match the complete marking
Include 22810-00-04-10-02 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 22810-00-04-10-02 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 22810-00-04-10-02
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:22810-00-04-10-02
-
Weight:0.14 kg
-
Tariff Code:8537101190
-
Transducer series:7200 Series 5 mm and 8 mm
-
Probe tip diameter:8 mm
-
Mounting configuration:Standard mount
-
Mounting thread:M10 x 1
-
Lead armor:Stainless steel
-
Unthreaded length:0 mm
-
Overall case length:40 mm
-
Total probe length:1.0 m
-
Connector:Miniature male coaxial connector
-
Connector code:02
-
Order-code fields:Five fields after 22810
-
Measurement principle:Non-contact eddy-current proximity measurement
-
Measured quantities:Static position and dynamic vibration
-
Companion electronics:Matching 7200 Series extension cable and Proximitor
-
System boundary:Legacy 7200 chain; do not apply 3300 XL ratings
Information
- Bently Nevada 22810-00-04-10-02 is an armored M10 x 1 standard-mount 8 mm probe for a legacy 7200 proximity transducer chain.
Selected mechanics: M10 x 1; 0 mm unthreaded; 40 mm case.
Lead selection: 1.0 m armored lead with miniature male coaxial connector.
The 1.0 m lead uses stainless-steel armor and a miniature male coaxial connector. Preserve the installed 7200 extension-cable and Proximitor identities because their electrical relationship belongs to the legacy chain.
The probe is a passive eddy-current sensing element. Commissioning restores the documented gap or bias and proves the complete 7200 monitor channel against the recorded machine baseline; 3300 XL system values are not transferred.
-
Bently Nevada 22810-00-04-10-02 official technical excerpt
Selected manufacturer pages covering the applicable family, technical data and exact order-code fields. -
Bently Nevada 22810-00-04-10-02 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below require the documented 7200 Series 5 mm and 8 mm proximity transducer system companion components and approved machine drawing.
-
Radial shaft vibration
Use the complete matched transducer chain at a documented bearing location to observe shaft motion relative to the probe mounting. -
Axial position
Aim the probe at an approved conductive thrust target and keep the expected travel inside the characterized linear region. -
Phase reference
Use only where the installed target feature and monitoring channel are approved for once-per-turn phase reference. -
Installed-channel maintenance
Preserve the recorded probe, extension cable, Proximitor, target material, mounting geometry and monitor assignment.
Match every field of 22810-00-04-10-02 with the installed spare-parts and channel records.
Prevent impact, metal-particle contact and contamination at the probe tip during handling.
Record thread engagement, reach, lock position, target relationship and as-found gap or bias before removal.
Maintain the approved bend radius, connector protection and independent strain relief; do not twist the probe lead.
Use the approved stopped-machine procedure to restore the documented gap or bias.
Verify as-left electrical indication and controlled machine response against the accepted baseline.
Alternative Names
Technical notes
Mechanical relationship: The M10 x 1 mounting, 0 mm unthreaded section and 40 mm case establish probe position.
Legacy-chain relationship: Use the 1.0 m armored lead only with the documented 7200 extension cable and matching Proximitor.
Technical reference: Bently Nevada 7200 Proximity Transducer Systems 5 mm and 8 mm Technical and Ordering Information.
FAQ View All FAQ
-
How should the installed port be checked before fitting 22810-00-04-10-02?Compare the M10 x 1 mounting, 0 mm unthreaded section and 40 mm case with the machine drawing, record the as-found datum and verify that expected target travel will remain clear before the old probe is moved.
-
Which companion electronics must be retained with 22810-00-04-10-02?Keep 22810-00-04-10-02 inside the documented 7200 Series 5 mm and 8 mm proximity transducer system; confirm the extension-cable and Proximitor identities and the selected total system length.
-
What connector inspection is required for 22810-00-04-10-02?The selected interface is miniature male coaxial connector. Isolate the channel, inspect mating surfaces for moisture, contamination and damage, then seat and support the connection without lead strain.
-
How is the operating point restored after installing 22810-00-04-10-02?Use the approved stopped-machine method to restore the recorded gap or bias, then perform a gap or bias and monitor-response comparison against the recorded 7200 baseline.
-
How should target material be handled when accepting 22810-00-04-10-02?Use the documented target material and geometry for the installed machine; a different alloy, curvature or target area can change scale and linearity.
-
What check helps separate a probe fault from a monitor fault on 22810-00-04-10-02?Compare the stopped-machine gap or bias at the Proximitor with the local monitor indication, then inspect the probe and cable path before substituting electronics.
-
When must 22810-00-04-10-02 be withheld from service?Do not release the channel if identity, mounting geometry, connector, companion electronics, target relationship or controlled response differs from the approved record.
-
What as-left evidence should be retained for 22810-00-04-10-02?Retain the complete marking, legacy companion identities, installed datum, as-left gap or bias and returned monitor response.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
22810-00-04-10-02Product Details -
330101-00-20-10-01-00Product Details -
330102-20-96-10-02-05Product Details -
330101-01-39-10-01-05Product Details -
330101-01-29-10-01-05Product Details -
3500/15 106M1079-01Product Details -
21504-000-032-10-02Product Details -
330130-085-02-CNProduct Details -
330930-065-04-05Product Details -
330930-065-02-00Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






