Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for IS200VTURH1BAA
For more information on how your data is processed and stored by Apterpower please read our privacy policy
Technical specifications for IS200VTURH1BAA
-
Manufacturer:General Electric
-
Product Category:Gas Turbine Control
-
Spare Part Number:IS200VTURH1B
-
Estimated shipping dimensions:2.1x18.8x26.2cm
-
Weight:0.3 kg
-
Tariff Code:8537101190
-
Counliy of origin:USA
-
MPU Pulse Rate Range:2 Hz to 20 kHz
-
MPU Pulse Rate Accuracy:0.05% of Reading
-
Number of Trip Solenoids:3
-
Operating Temperature Range:-40°C to +70°C
-
Environmental Rating:Industrial Grade
-
Communication Interface:RS-485
-
Power Supply Voltage:24V DC
Information
Overview
Manuals
Common Applications
Product Precautions
The IS200VTURH1BAA is a VME-bus Turbine Specific Primary Trip Board designed for the Mark VI Speedtronic control system architecture. Functioning as a critical hardware-level protection asset, this board interfaces directly within the control rack to process primary turbine protection parameters, including shaft overspeed, acceleration, and emergency manual trips.
- Relay Output Controls for Emergency Shutdown
- Dual Flame Detector Signal Processing Channels
- Direct Integration into VME Rack Enclosures
The IS200VTURH1BAA executes embedded overspeed detection algorithms and hardware-level vote logic (such as two-out-of-three matrix configurations). Upon detecting any violation of pre-programmed trip limits or receiving external emergency shutdown commands, the board immediately de-energizes its onboard electro-mechanical trip relays, venting hydraulic fluid to shut off fuel or steam valves.
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
General Electric IS200VTURH1BAA Protection Board Manuals, Datasheets, Drivers, Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in t330101-00-16-10-01-05n.
Thermal Power Generation
Monitors shaft speed of primary steam turbine generators in coal or gas-fired power plants, directly de-energizing emergency trip systems (ETS) to close main stop valves during sudden load rejection or overspeed.
Nuclear Power Industry
Provides safety-compliant primary trip protection for high/low-pressure main steam turbines and high-power reactor feedwater pump turbines in the conventional island of nuclear power plants.
Petrochemical & Refining
Used for emergency safety shutdown protection of driving turbines for large cracked gas compressors and rich gas compressors in million-ton ethylene plants or refineries.
Coal Chemical Industry
Monitors large air separation turbine compressor units and syngas compressor units in coal-to-liquids or coal-to-methanol plants to prevent turbine runaway overspeed.
Iron & Steel Metallurgy
Utilized for speed monitoring and two-out-of-three trip voting on blast furnace Top Gas Recovery Turbine (TRT) power generation units and blast furnace blower-driving turbines.
Seawater Desalination
Provides overspeed safety control for high-pressure steam driving turbines or large high-pressure pump shafts acting as primary power sources in large thermal or membrane desalination plants.
Completely isolate and power down the system before inserting, removing, or wiring the module within the VME rack; live operation is strictly prohibited to prevent electronic component damage. During commissioning and maintenance, configure the over-speed trip and flame monitoring channel parameters strictly according to the Mark VI control manuals, and ensure that field sensor cable shields are correctly grounded to suppress electrical noise interference.
Technical notes
The IS200VTURH1BAA features dedicated diagnostic LEDs on its front panel to indicate communication status (TX/RX), card health status (OK), and active trip conditions. Through the VME backplane, the board transmits real-time speed data, hardware self-test diagnostic codes, and trip sequence event logs to the central HMI for troubleshooting and chronological fault analysis.
FAQ View All FAQ
-
What is IS200VTURH1BAA?IS200VTURH1BAA is a Turbine Specific Primary Trip Board.
-
What is the GE IS200VTURH1BAA Protection Board used for?The IS200VTURH1BAA is a primary turbine protection card for GE Mark VI/VIe systems, providing safety and trip functions for gas and steam turbines.
-
Which control systems is the IS200VTURH1BAA compatible with?The IS200VTURH1BAA works with GE Mark VI and Mark VIe turbine control platforms.
-
What protection functions does the IS200VTURH1BAA perform?It manages overspeed protection, flame detection, shaft voltage/current monitoring, and emergency trip execution.
-
Which types of turbines can the IS200VTURH1BAA be used with?The IS200VTURH1BAA supports both industrial gas turbines and steam turbines.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.