-
Match the complete marking
Match the complete Siemens 6ES5451-4UA12 marking and actual installed configuration. Check the enable-mode jumper, front connector coding and output-group fuses.
-
Check the offered item before ordering
Compare offered-unit photographs, interfaces and included items with the installed 6ES5451-4UA12 and its applicable installation requirements.
Technical specifications for 6ES5451-4UA12
-
Manufacturer:Siemens
-
Product Category:PLC Systems
-
Spare Part Number:6ES5451-4UA12
-
Weight:0.46 kg
-
Tariff Code:8537101190
-
Digital outputs:32
-
Field supply range:20–30 V DC
-
Output current:5 mA to 0.5 A
-
Total current per eight outputs:4 A maximum
-
Group fuse:6.3 A slow, one per eight outputs
-
Off-state leakage:0.5 mA maximum
-
Resistive switching frequency:100 Hz maximum
-
Lamp load:5 W maximum
-
Backplane consumption:5 V, 120 mA typical
Information
- Siemens 6ES5451-4UA12 connects the S5 output image to DC actuators while separating the backplane logic interface from the floating field-output group.
Service interface: Enable input with selectable operating behavior
Load selection: Distinct resistive, inductive and lamp switching limits
The enable circuit affects how the module participates in the system. The -4UA12 version includes an enable-mode selection; preserve its actual setting and the associated field wiring when replacing an installed module.
Load type changes the permissible switching frequency. Inductive energy, lamp inrush and cabinet cooling must be evaluated against their respective limits, followed by a controlled channel-by-channel output test.
6ES5451-4UA12 Original Technical Excerpt
SIMATIC S5 U Peripheral Equipment, Digital Modules. Selected original pages retain the relevant technical tables and interface context. PDF · 6 pages.6ES5451-4UA12 Installation & Verification Guide
Apter Power field guide covering record group and enable allocation, check load duty and cabinet cooling, restore the output interface, validation and handover. PDF · 5 pages.
Application scope: The applications below describe the installed measurement or control path. Select compatible companion equipment; accessories are included only when expressly itemized.
DC solenoid control
Switch approved DC actuator circuits from the S5 output map.Contactor command
Drive coils within the inductive switching-duty limits.Grouped output maintenance
Locate faults using the eight-channel indication and fuse arrangement.Legacy rack restoration
Retain module address and enable behavior in an existing S5 installation.
Identify the four eight-output load groups, their fuses and their field-supply feeds. Record the module address and enable-mode jumper before disconnecting the front connector.
Review actual resistive, inductive and lamp loads separately. Add the currents in each output group and assess simultaneous loading against the available cabinet ventilation.
Place actuators in a safe maintenance state, isolate the relevant supplies and follow the S5 module replacement procedure. Reconnect the coded front connector and reinstate the recorded address and enable arrangement.
Command representative outputs individually before testing the required simultaneous state. Observe channel indications, group short-circuit indications and the physical release of each load.
Run the authorized sequence while observing interlocks and coil duty. Record the final fuse types, enable setting, affected output addresses and load checks for the maintenance handover.
Retain the final 6ES5451-4UA12 identity, tested settings and accepted channel or system response for subsequent maintenance.
Alternative Names
Technical notes
Thermal diversity: Without forced ventilation, simultaneous-load diversity is reduced above 35 °C. Assess the cabinet conditions and aggregate output loading instead of relying solely on the individual-channel rating.
Inductive switching: The permitted inductive switching rate decreases with load current. Use the actual coil current and suppression arrangement in the switching-duty assessment.
Group fault response: A short-circuit indication identifies an output group. Isolate and investigate its field circuits before replacing the module or increasing protection ratings.
FAQ View All FAQ
-
Why can 6ES5451-4UA12 overheat even when no individual output exceeds its rated current?Group totals and simultaneous-load diversity still apply. Evaluate cabinet cooling and the number of energized outputs, especially without forced ventilation above 35 °C.
-
How does an inductive load affect the switching duty of 6ES5451-4UA12?The permitted rate is lower than for a resistive load and depends on coil current. Assess the actual coil and suppression circuit rather than using the resistive switching limit.
-
What does a group short-circuit indication on 6ES5451-4UA12 help isolate?It narrows the investigation to a group of eight outputs. Check the affected wiring, load and fuse before concluding that the entire module has failed.
-
Why should the enable-mode jumper on 6ES5451-4UA12 be photographed before removal?Its setting changes the enable-input behavior. Retaining the installed setting prevents a replacement from behaving differently despite identical output wiring.
-
Can a lamp circuit be selected for 6ES5451-4UA12 using steady-state current alone?No. Lamp inrush and the separate lamp-load rating must be considered in addition to the steady-state current.
-
Does current limiting on 6ES5451-4UA12 replace the specified group fusing?No. Current limiting and group fuses serve different functions. Preserve the specified protection arrangement and investigate the cause of a blown fuse.
-
How can an apparently inactive output on 6ES5451-4UA12 still influence a sensitive load?The off-state has finite leakage. Confirm that the load remains positively released at the permitted leakage level rather than treating an off command as an open circuit.
-
What should be checked when all outputs on 6ES5451-4UA12 remain inactive but the CPU is running?Check field supply, group protection, enable wiring and the selected address before changing the program. A running CPU alone does not establish a healthy field-output path.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.



