-
Match the complete marking
Provide the complete Bently Nevada 330525-01 marking. Verify 330525-01 and the actual approval marking and connector assembly.
-
Check the offered item before ordering
Request available label and connector photos. Have your maintenance team compare the offered 330525-01 with the installed equipment and applicable Bently Nevada instructions.
Technical specifications for 330525-01
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330525-01
-
Weight:0.16 kg
-
Tariff Code:8537101190
-
Sensitivity:3.94 mV/mm/s (100 mV/in/s), ±5%
-
Frequency response:4.5–2000 Hz, ±3 dB
-
Flat-response band:6–1000 Hz, ±0.9 dB
-
Supply:−22 to −30 V DC
-
Bias current:2.5–6.0 mA
-
Output bias:−12 ±3 V DC over temperature, referenced to pin A
-
Dynamic impedance:<2,400 Ω
-
Velocity amplitude:1,270 mm/s peak
-
Amplitude linearity:±2% to 152 mm/s peak
-
Operating temperature:−55 to +121 °C
-
Connector:2-pin MIL-C-26482
-
Case material:316L stainless steel
Information
- Bently Nevada 330525-01 combines a rugged field connection with velocity-proportional sensing where the installation needs protection against dust and moisture.
Response: 4.5–2000 Hz within ±3 dB
Installation: Weatherproof mating-cable assembly
The sensor requires −22 to −30 V DC and a 2.5–6.0 mA bias current. Output bias is −12 ±3 V DC over temperature referenced to pin A. Signal polarity, supply polarity and the receiving channel configuration must be kept consistent.
The case is isolated and uses a two-pin MIL-C-26482 connector. The IP65/NEMA 4X installation claim requires the properly fitted mating extension cable. The operating range is −55 to +121 °C, and a hermetically sealed case does not authorize submersion.
330525-01 Official Technical Excerpt
Bently Nevada 330525-01: original manufacturer technical information covering the specified interfaces and operating limits. PDF · 7 pages.330525-01 Installation & Verification Guide
Apter Power installation and verification guide covering choose a representative housing point, confirm the negative supply, set the velocity sensitivity, test within the response band, compare the installed vibration signal. PDF · 5 pages.
Application scope: The applications below describe its technical role. Select associated hardware and configuration for the actual installation.
Outdoor housing vibration
Use the correctly sealed mating-cable arrangement in a suitable non-submerged installation.Low-frequency velocity monitoring
Measure within the 4.5 Hz lower response boundary with the appropriate tolerance.Rugged process machinery
Use the stainless-steel sensor body and compatible field connection for housing measurements.Velocity-channel replacement
Preserve sensitivity, negative supply and polarity when restoring an installed channel.
Inspect the mating extension-cable assembly and connector seals. The environmental installation rating depends on this connection being complete and correctly fitted.
Record the measurement direction and pin-A polarity convention. This is important when comparing phase or motion direction with another channel.
Measure powered bias and assess it against the −12 ±3 V DC specification over temperature. Resolve a supply or cable fault before dynamic testing.
Maintain the specified cable bend allowance and protect the joint from mechanical load. Keep the connection intact in wet or dusty locations.
Save mounting position, cable assembly, electrical measurements and verification conditions. Confirm that the application remains non-submerged and within the operating-temperature range.
Verify the sensor and receiving channel against a suitable reference at the same location and direction. Investigate mounting resonance before changing calibration values.
Alternative Names
Technical notes
Operating boundary: The 1,270 mm/s peak amplitude limit and the ±2% linearity statement to 152 mm/s peak describe different performance boundaries.
Integration details: Match the -01 approval marking, mating cable, supply circuit, sensitivity and housing mount before replacing the sensor.
Technical basis: Bently Nevada 330525 Velomitor XA Piezo-velocity Sensor, 141633 Rev. M. 330525 performance is specified at +20 to +30 °C and 100 Hz unless stated otherwise. Environmental sealing depends on proper installation with the mating cable; approval applicability follows the actual -01 marking.
FAQ View All FAQ
-
Does the IP65/NEMA 4X installation rating of 330525-01 apply with an open connector?No. It requires proper installation with the mating extension-cable assembly. The connector interface is part of the environmental boundary.
-
What velocity scaling is required for 330525-01?Use 3.94 mV/mm/s, equivalent to 100 mV/in/s, at the stated nominal conditions rather than another Velomitor variant's sensitivity.
-
Which supply polarity does 330525-01 require?The specified supply is negative, −22 to −30 V DC, with 2.5–6.0 mA bias current. Preserve the applicable wiring and polarity.
-
How does 330525-01 polarity relate to physical motion?Pin A goes positive relative to pin B when the sensor case moves toward the connector. Keep that convention when comparing phase or polarity.
-
Can 330525-01 be submerged because its case is hermetically sealed?No. The humidity specification is for non-submerged conditions. A sealed case does not establish a submersion rating for the complete assembly.
-
Why should a reading at 5 Hz on 330525-01 use the broader response tolerance?5 Hz lies inside the 4.5–2000 Hz ±3 dB band but outside the flatter 6–1000 Hz ±0.9 dB band.
-
Does case isolation on 330525-01 eliminate all field-grounding considerations?No. The case isolation is only one part of the installation. The cable, receiver and test-equipment grounding must follow the intended circuit arrangement.
-
What should be checked if 330525-01 has abnormal DC bias?Check supply voltage, bias current, polarity and cable connections against the specified circuit before interpreting the dynamic signal as valid vibration.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.










