-
Match the complete marking
Include the complete 330104-04-10-05-01-00 marking and photographs of the installed connection and mounting position.
-
Check the offered item before ordering
Request available-unit label and connector photographs. Have your maintenance team compare the offered 330104-04-10-05-01-00 with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330104-04-10-05-01-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330104-04-10-05-01-00
-
Weight:0.1 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL 8 mm
-
Mounting thread:M10 x 1
-
Armor:With armor
-
Unthreaded length:40 mm
-
Overall case length:100 mm
-
Total probe length:0.5 m
-
Connector and cable option:01 - ClickLoc with protector, standard cable
-
Agency approval option:00 - Not required
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 303 or 304 stainless steel
-
Cable construction:75 ohm triaxial, FEP insulated
-
System linear range:2.0 mm (80 mils), matched 3300 XL 8 mm system
-
System scale factor:7.87 V/mm (200 mV/mil)
-
Recommended radial-vibration gap:-9 V DC; approximately 1.27 mm
-
Frequency response:0 to 10 kHz, +0/-3 dB
-
Standard probe temperature:-52 to +177 deg C
-
Minimum cable bend radius:25.4 mm
Information
- The medium-reach metric probe uses standard FEP cable, stainless-steel armor and a connector-protected ClickLoc joint without an agency-approval option.
Compact armored connection: The 0.5 m lead is mechanically protected up to the detachable system joint.
Repeatable XL service: The documented 8 mm chain supports component interchange when family and electrical length remain matched.
The 0.5 m standard probe lead is enclosed in flexible stainless-steel armor and terminates in a protected ClickLoc connector. Extension-cable length is selected to complete the calibrated Proximitor Sensor chain.
System response is based on matched XL components and the specified AISI 4140 target. Final acceptance checks both physical position and the live electrical baseline rather than relying on mechanical fit alone.
330104-04-10-05-01-00 Official Datasheet Excerpt
Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet 141194 Rev. AN. Selected original pages covering the applicable product family, technical data and ordering information.330104-04-10-05-01-00 Installation & Verification Guide
Apter Power field guide covering identity capture, installed relationships, controlled replacement, commissioning and handover.
Application scope: Apply it to approved M10 x 1 machine points requiring the documented medium-reach case geometry.
Sleeved probe locations
Use the 40 mm unthreaded reach where the approved drawing calls for this insertion geometry.Protected local routing
The armored 0.5 m lead covers the short machine-side segment before the extension cable.Radial vibration channels
Maintain target diameter, probe spacing and the documented operating gap.Axial position channels
Check target travel and locknut stability before return to service.
Do not accept a visually similar M10 probe with different reach or case length.
Measure the installed position before removing the armored probe.
Torque the case while keeping the lead and ferrule free from twist.
Clean, seat and cover the connection without exceeding bend limits.
Select the extension cable for the installed Proximitor Sensor.
Confirm gap voltage and machine signal against the accepted record.
Alternative Names
Technical notes
Exact configuration: Armored M10 x 1 probe, 40 mm unthreaded length, 100 mm case, 0.5 m lead, connector protector and no approval option
Selection boundary: The 40/100 mm geometry is not interchangeable with another 330104 case without installation review
Technical reference: Bently Nevada 3300 XL 8 mm Proximity Transducer System Datasheet 141194 Rev. AN
FAQ View All FAQ
-
How does 330104-04-10-05-01-00 differ from a longer 330104 execution?It specifically uses 40 mm unthreaded reach and a 100 mm case; both values control installed tip position.
-
What should be measured before removing 330104-04-10-05-01-00?Measure the locknut datum, insertion depth, sleeve clearance, cable route and the current electrical gap.
-
Why is 330104-04-10-05-01-00 supplied with armor?The 330104 family is the armored M10 x 1 execution, providing mechanical protection around the probe lead.
-
What protection is included at the connector of 330104-04-10-05-01-00?Option 01 adds a protector over the miniature ClickLoc connection on the standard cable.
-
Can 330104-04-10-05-01-00 be used in a 1 m system without an extension cable?No. Its probe lead is 0.5 m, so the extension cable and Proximitor Sensor must be selected to create the intended system length.
-
Which approval claim is justified by 330104-04-10-05-01-00?The final 00 option does not select agency approvals; use only the approvals documented for the complete supplied installation.
-
How should 330104-04-10-05-01-00 be checked for cable stress?Confirm no twist at the armored ferrule, at least 25.4 mm bend radius and independent support away from the ClickLoc joint.
-
What commissioning result is retained for 330104-04-10-05-01-00?Retain the as-left position, gap voltage, runout and measured vibration or position response with the complete channel identity.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330104-04-10-05-01-00Product Details -
330103-17-22-10-12-05Product Details -
330103-00-08-10-12-05Product Details -
330103-00-04-10-01-00Product Details -
330103-06-20-10-02-00Product Details -
330104-10-16-05-01-00Product Details -
330103-00-05-10-01-05Product Details -
330102-00-25-10-02-05Product Details -
330102-00-27-10-02-05Product Details -
330102-00-52-10-02-00Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.







