Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for 330103-00-11-10-02-05
For more information on how your data is processed and stored by Apterpower please read our privacy policy
-
Match the complete marking
Include the complete Bently Nevada 330103-00-11-10-02-05 marking and any hardware revision on the item. Compare the complete order code, mating interfaces and installed measurement chain.
-
Check the offered item before ordering
Request available label and connector photos. Have your maintenance team compare the offered 330103-00-11-10-02-05 with the installed equipment and applicable Bently Nevada documents.
Technical specifications for 330103-00-11-10-02-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330103-00-11-10-02-05
-
Weight:0.05 kg
-
Tariff Code:8537101190
-
Tip diameter:8 mm
-
Mounting thread:M10 x 1
-
Case length:110 mm
-
Unthreaded section:0 mm
-
Probe length:1.0 m
-
Probe resistance:7.59 ohm ±0.50 ohm
-
System linear range:2 mm
-
System scale factor:7.87 V/mm
-
Reference gap:1.27 mm
-
Calibration target:AISI 4140 steel
Information
Overview
Downloads
Applications / Compatibility
Product Precautions
- Bently Nevada 330103-00-11-10-02-05 brings the XL 8 mm sensing element to a deeper metric mounting point without changing the one-metre probe lead arrangement.
Mounting: M10 x 1; 110 mm case; 0 mm unthreaded
Lead configuration: 1.0 m; unarmored standard cable
Matched-system scale: 7.87 V/mm
Lead configuration: 1.0 m; unarmored standard cable
Matched-system scale: 7.87 V/mm
The selected 110 mm case and M10 x 1 thread provide the mechanical reach for the sensing point. Its entire case selection is independent of the 1.0 m total probe length used in the electrical system.
The unarmored standard cable uses a miniature ClickLoc connector. A 4.0 m compatible extension forms a 5.0 m chain with this probe; a different total length requires the corresponding Proximitor calibration.
The probe operates as part of the XL 8 mm eddy-current system. Standard sensitivity assumes the specified steel target and operating conditions, so a resistance check and a gap check are complementary rather than interchangeable acceptance tests.
The unarmored standard cable uses a miniature ClickLoc connector. A 4.0 m compatible extension forms a 5.0 m chain with this probe; a different total length requires the corresponding Proximitor calibration.
The probe operates as part of the XL 8 mm eddy-current system. Standard sensitivity assumes the specified steel target and operating conditions, so a resistance check and a gap check are complementary rather than interchangeable acceptance tests.
Controller platform reference: 3300 XL 8 mm Proximity Transducer System. Follow the applicable installation instructions and approved measurement-chain design.
The original technical excerpt applicable to Bently Nevada 330103-00-11-10-02-05 covers system performance, probe connections and applicable order selections. The separate installation guide covers mounting, cable matching, target clearance, gap and signal checks.
330103-00-11-10-02-05 Official Technical Excerpt
The original technical excerpt applicable to Bently Nevada 330103-00-11-10-02-05 covers system performance, probe connections and applicable order selections. PDF · 6 pages.330103-00-11-10-02-05 Installation & Verification Guide
Apter Power installation and verification guide covering mounting, cable matching, target clearance, gap and signal checks. PDF · 5 pages.
Original manufacturer pages retain their technical context. Use the Apter Power guide with the applicable manufacturer instructions and approved installation design.
System and supply context: The probe works with the corresponding extension cable and Proximitor; the supplied item does not include the complete measurement channel.
Application scope: Apply the M10 x 1 installation to its intended target and keep the selected 1.0 m probe length in the electrical-length calculation.
Application scope: Apply the M10 x 1 installation to its intended target and keep the selected 1.0 m probe length in the electrical-length calculation.
Prepare Bently Nevada 330103-00-11-10-02-05 for its configured installation using these checks.
Mounting interface
Match the M10 x 1 installation and selected case geometry.
Cable handling
Retain the unarmored standard cable construction and avoid connector strain.
Electrical length
Match the probe and extension cable to the Proximitor calibration.
Target calibration
Assess target material and clearance before applying nominal sensitivity.
Gap setting
Establish the gap using the complete energized measurement chain.
Channel test
Check static response, dynamic indication and configured alarms.
Alternative Names
330103 00 11 10 02 05
Bently Nevada 330103-00-11-10-02-05
Technical notes
Signal and interface: The 2 mm linear range and 7.87 V/mm scale factor belong to the complete matched system; the probe alone does not establish these ratings.
Installation boundary: The reference gap is 1.27 mm (approximately -9 V for radial vibration). Confirm target material, available travel and correct total electrical length before using the nominal calibration.
Technical basis: Bently Nevada 3300 XL 8 mm Proximity Transducer System, 141194 Rev. AN. Ordering selections apply to this complete probe code. Range, scale factor and gap are matched-system values under the specified calibration conditions.
FAQ View All FAQ
-
How does the 110 mm case of 330103-00-11-10-02-05 affect installation?It determines the physical reach and threaded engagement; it does not change the selected 1.0 m electrical probe length.
-
Which extension length pairs with 330103-00-11-10-02-05 in a 5 m system?A compatible 4.0 m extension plus the 1.0 m probe makes the 5.0 m chain.
-
What resistance is nominal for the probe in 330103-00-11-10-02-05?The 1.0 m probe has nominal center-to-outer-conductor resistance of 7.59 ohm ±0.50 ohm.
-
What thread pitch must match 330103-00-11-10-02-05?The metric interface is M10 x 1; an M10 thread with a different pitch is not interchangeable.
-
What output change should a 0.1 mm target movement produce with 330103-00-11-10-02-05?The nominal 7.87 V/mm matched-system scale corresponds to approximately 0.787 V, subject to calibration and operating conditions.
-
Does 330103-00-11-10-02-05 include a connector protector in option 02?Option 02 is the standard miniature coaxial ClickLoc connection without the option-01 connector protector.
-
What target material defines the nominal calibration of 330103-00-11-10-02-05?The standard system calibration uses AISI 4140 steel; a different target material can alter the scale.
-
Why check the final gap after locking 330103-00-11-10-02-05?Tightening and securing the installation can shift the probe; verify the energized channel remains at the intended reference position.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.