The 330102-00-40-10-02-05 is an 8 mm proximity probe from the Bently Nevada 3300 XL series, designed for high‑precision industrial machinery monitoring. It features a 3/8‑24 UNF threaded housing, PPS probe tip, and ClickLoc miniature coaxial connector, allowing seamless integration into 3300 XL monitoring systems.
High Accuracy
Wide Temperature
Rugged Construction
This probe delivers accurate shaft displacement and vibration measurements with a linear range of 0.25–2.3 mm and a typical frequency response up to 10 kHz. Operating reliably from –35 °C to +120 °C, its stainless steel housing ensures durability in harsh industrial environments, providing continuous monitoring for critical rotating machinery.
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
Bently Nevada 330102-00-40-10-02-05 8 mm Proximity Probes Manuals, Datasheets, Drivers, Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
Rotating Machinery
Used in turbines, compressors, and generators to continuously monitor shaft position and vibration. Provides early detection of imbalance, misalignment, and looseness, preventing potential equipment failure.
Power Generation
Applied in fossil fuel, hydro, and nuclear power plants to monitor critical rotating equipment. Supports real-time detection of shaft displacement anomalies, enabling predictive maintenance.
Oil & Gas
Implemented in pumps, compressors, and pipelines across upstream, midstream, and downstream facilities. High accuracy monitoring ensures safe operation under high temperatures and harsh conditions.
Petrochemical Plants
Used in centrifugal pumps, compressors, and turbines within chemical processing facilities. Provides precise vibration and displacement feedback to detect bearing wear and shaft instability early.
Marine & Offshore
Installed on shipboard propulsion systems, generators, and pumps. Rugged construction and wide temperature tolerance allow reliable monitoring in harsh marine environments.
Pulp & Paper
Monitors rolls, fans, and turbine shafts in paper mills and pulp manufacturing. Detects imbalance, misalignment, and vibration deviations to prevent equipment damage.
The 330102‑00‑40‑10‑02‑05 8 mm proximity probe is part of the 3300 XL Proximity Transducer System, which provides continuous measurement of shaft displacement and vibration.Proper installation of the probe requires following the 3300 XL system guidelines on probe spacing and alignment to ensure linear output across the specified sensing range. This guarantees accurate static and dynamic measurements for conditioned monitoring systems.
That the 3300 XL series uses a non‑contact eddy‑current principle, where the probe’s output voltage is proportional to the distance between the probe tip and the target surface. The recommended measurement range and system frequency response up to 10 kHz are specified to maintain reliable performance when connected to 3300 XL Proximitor® electronics and monitor modules.
The 330102‑00‑40‑10‑02‑05 is an 8 mm proximity probe designed for the 3300 XL Proximity Transducer System. It measures shaft displacement and vibration for machinery condition monitoring and protection.
What are the key measurement specifications of 330102‑00‑40‑10‑02‑05?
This probe provides a linear measurement range of approximately 0.25 mm to 2.3 mm and a typical frequency response up to 10 kHz. These specifications support accurate static position and dynamic vibration readings.
What temperature conditions can 330102‑00‑40‑10‑02‑05 withstand?
Standard operating temperatures for the 3300 XL probes typically range from –35 °C to +120 °C per system datasheet specifications. The rugged design ensures reliable performance in industrial environments.
How is 330102‑00‑40‑10‑02‑05 installed?
It features a 3/8‑24 UNF threaded housing with no unthreaded length, plus a ClickLoc miniature coaxial connector. Proper alignment and spacing according to the 3300 XL user guide are critical for accurate measurement.
Does 330102‑00‑40‑10‑02‑05 require a separate power source?
No, the probe does not require its own power. It is powered by the associated 3300 XL Proximitor Sensor electronics, which provide excitation and condition the signal to the monitor.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
Please try to be as accurate as possible with your search.
We can quote you on 1000s of specialist parts, even if they are not listed on our website.