-
Match the complete marking
Match the complete B&R 3IF661.9 marking, hardware revision and selected configuration to the installed position. Check network role and physical interface against the installed configuration.
-
Check the offered item before ordering
Request label and connection photographs. Have your maintenance team compare the offered 3IF661.9 with the installed equipment and applicable B&R instructions.
Technical specifications for 3IF661.9
-
Manufacturer:B&R
-
Product Category:PLC Systems
-
Spare Part Number:3IF661.9
-
Weight:0.14 kg
-
Tariff Code:8537101190
-
Network role:PROFIBUS DP slave
-
Physical interface:Electrically isolated RS485
-
Connector:Female 9-pin D-sub
-
Protocol controller:SPC3
-
Integrated controller RAM:1.5 KB
-
Host supply:5 V DC
-
Maximum power consumption:2 W
-
Station address selection:Two BCD switches
-
12 Mbit/s cable length:Less than 100 m
-
1.5 Mbit/s cable length:Less than 200 m
-
500 kbit/s cable length:Less than 400 m
-
187.5 kbit/s cable length:Less than 1000 m
Information
- B&R 3IF661.9 connects a System 2005 station to a PROFIBUS master through a shielded RS485 bus while retaining a locally selected station address.
Physical interface: Electrically isolated RS485
Connector: Female 9-pin D-sub
The isolated RS485 interface uses a female 9-pin D-sub connector. Two BCD switches select the station number, and RXD/TXD indicators show receive and transmit activity. Cable length must be selected for the network transmission rate.
An external T-connector with the correct terminating resistor is required at the bus end. Shield contact, data-line polarity and station addressing must be checked together; replacing the interface alone does not correct an incorrectly terminated network.
3IF661.9 Official Technical Excerpt
Original B&R technical material applicable to 3IF661.9, covering function, interfaces and operating limits. PDF · 4 pages.3IF661.9 Installation & Verification Guide
Apter Power field guide for the selected connection, configuration and functional tests. PDF · 5 pages.
Application scope: The technical values apply to this model in the specified installation and configuration. The examples below address the stated product function.
System 2005 slave integration
Exchange process data between a compatible local host and the PROFIBUS DP master.Legacy interface maintenance
Restore a CP260, IF260 or IF060 station using its retained bus address and configuration.High-speed PROFIBUS segment
Operate a short, correctly terminated segment at the selected baud rate.Communication fault isolation
Use station addressing, bus polarity and RXD/TXD activity to distinguish local interface issues from network wiring faults.
Check whether the interface is installed in a CP260, IF260 or IF060.
Record the station number selected by the two BCD switches and the master's assigned slave configuration.
Reconnect the data pair to the designated D-sub contacts.
Maintain the shield connection through the connector housing and prescribed grounding arrangement.
Compare the actual segment length with its operating baud rate.
Confirm which physical nodes are at the two ends of the segment.
Alternative Names
Technical notes
Preserve the DP slave identity: Record the station number selected by the two BCD switches and the master's assigned slave configuration. A replacement with a different address may be electrically connected but invisible to the intended master assignment.
Match segment length to baud rate: Compare the actual segment length with its operating baud rate. The limits are less than 100 m at 12 Mbit/s, 200 m at 1.5 Mbit/s, 400 m at 500 kbit/s and 1000 m at 187.5 kbit/s.
Retain the network service record: Record the host, slave address, baud rate, segment length and termination state. These details make future replacement reproducible and help distinguish a recurrent network fault from a problem in the replacement interface.
FAQ View All FAQ
-
Can 3IF661.9 control a PROFIBUS network as the master?No. IF661 is a PROFIBUS DP slave interface; the bus master must be provided elsewhere in the network.
-
Which System 2005 hosts can carry 3IF661.9?The designated hosts are CP260, IF260 and IF060. Verify the installed host and slot before replacing the interface.
-
How is the station number set on 3IF661.9?Two BCD switches set the station number. Preserve the assigned address and check that no other slave uses it.
-
Why can 3IF661.9 work at a low baud rate but fail at 12 Mbit/s?Permissible cable length decreases with speed. At 12 Mbit/s the cable length must be less than 100 m; termination and shielding also become critical to signal integrity.
-
Which connector carries the PROFIBUS signals on 3IF661.9?A female 9-pin D-sub carries the isolated RS485 connection. Pin 3 is DATA and pin 8 is the complementary data signal.
-
What do the RXD and TXD indicators on 3IF661.9 show?They indicate receive and transmit activity respectively. Activity alone does not prove that all configured process data are valid.
-
Does 3IF661.9 isolate the fieldbus from the host electronics?Yes. The RS485 PROFIBUS interface is electrically isolated. Preserve the specified shield and reference connections when restoring the bus.
-
Where is bus termination provided for 3IF661.9?Termination is provided through the external T-connector arrangement. Enable the appropriate terminating resistor at the physical ends of the bus.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.



