Which ABB drives can use RPBA-01 3ABD64606859?

Use it only where the installed ABB drive documentation provides the compatible option slot and RPBA-01 support. Confirm the drive type, control-board execution, firmware and option-slot assignment before installation.

What network role does RPBA-01 3ABD64606859 perform?

It operates as a PROFIBUS DP slave and exchanges control, reference, status, actual-value and parameter data with a compatible PROFIBUS DP master.

How is the station address set for RPBA-01 3ABD64606859?

Record the approved node assignment and reproduce it using the module address controls or the supported configuration method. The documented station address range is 0 to 126, while the rotary-switch range is 00 to 99.

Which GSD file should be used for RPBA-01 3ABD64606859?

Match the project to the communication mode documented for the installation: ABB_0812.GSD for DP-V0 or ABB10812.GSD for DP-V1, then verify the selected PPO and I/O mapping.

How should PROFIBUS termination be checked for RPBA-01 3ABD64606859?

Termination must be active at the first and last station of the segment only. Confirm the connector termination switch, module power and shield grounding before enabling communications.

What should be recorded before replacing RPBA-01 3ABD64606859?

Record the drive and option slot, node address, GSD, PPO type, process-data map, cable routing, termination state, shield connection, hardware version and diagnostics.

How is RPBA-01 3ABD64606859 commissioned after replacement?

Restore the approved drive and master configuration, confirm master recognition, compare cyclic input and output words, verify authorized acyclic access and review both drive and network diagnostics.

Can RPBA-01 3ABD64606859 be moved to another PROFIBUS segment without verification?

No. Revalidate node uniqueness, baud-rate compatibility, cable length, termination, shield grounding, GSD, PPO mapping and the receiving control-system database before service.

RPBA-01 3ABD64606859

Name: RPBA-01 3ABD64606859
Brand: ABB
SKU: 3ABD64606859

PROFIBUS DP Adapter Module

Product image is representative; revision or series may vary. Contact us to request a specific version.

Product Describe：

ABB RPBA-01 3ABD64606859 is an optional PROFIBUS DP adapter module for ABB drives. It connects the installed drive as a slave to a PROFIBUS DP or DP-V1 control network.

Ask our team:

Phone: +86 180 3023 5313 E-Mail: sales13@apterpower.com

Dispatch Planning
Confirm stock and lead time with our team.

Dedicated Manager
Personalized one-to-one VIP service

ISO 9001:2015 Certified
Trusted quality management

Get a quick price for RPBA-01 3ABD64606859

E-mail *

Mobile *

Company

Content *

Quantity *

Upload (gif, jpg, jpeg, png, bmp, doc, docx, xls, xlsx, ppt, pdf, csv)

Get a Quote

For more information on how your data is processed and stored by Apterpower please read our privacy policy

What happens after you enquire

1

Requirement review

We review the part number, quantity and delivery requirements and ask for any missing details.
2

Quotation and availability

We confirm the proposed item, condition, availability, price and estimated lead time in the quotation.
3

Order confirmation and dispatch

Once the quotation and purchasing details are agreed, your contact will coordinate the order and available dispatch information.

Technical specifications for RPBA-01 3ABD64606859

Manufacturer:

ABB
Product Category:

General Automation
Spare Part Number:

3ABD64606859
Estimated shipping dimensions:

6.6x3.5x9.4cm
Weight:

0.06 kg
Tariff Code:

8537101190
Counliy of origin:

Sweden
Type designation:

RPBA-01
Supported fieldbus:

PROFIBUS DP, PROFIBUS DP-V1
Network role:

Slave
PROFIBUS connector:

9-pin female D-sub
Drive connection:

34-pin parallel bus connector
Station address range:

0 to 126
Hardware address range:

00 to 99
Supported PPO types:

1 to 6
Maximum cyclic input data:

28 bytes
Maximum cyclic output data:

28 bytes
Maximum cyclic I/O total:

56 bytes
Maximum acyclic I/O:

240 bytes input / 240 bytes output
Current consumption:

350 mA maximum at 5 V
Degree of protection:

IP20
Supported baud rates:

9.6 kbit/s to 12 Mbit/s

View as PDF Ask for Quote

Information

Overview Manuals Common Applications Product Precautions

RPBA-01 3ABD64606859 provides the PROFIBUS DP slave interface between a documented ABB drive and its control network.

Links an ABB drive to a PROFIBUS DP or DP-V1 master
Transfers drive control words, references, status and actual values
Supports cyclic PPO communication and acyclic DP-V1 services
Automatically detects the configured PROFIBUS transmission rate

The adapter is mounted in the approved drive option slot and communicates with a compatible PROFIBUS DP master through the 9-pin D-sub port. Engineering work covers the selected GSD file, node address, PPO telegram, parameter mapping, cable shield, segment termination and controlled drive diagnostics.

Important Notice: Confirm RPBA-01, 3ABD64606859, the installed ABB drive and option slot, adapter hardware version, 9-pin PROFIBUS connector, 34-pin drive connector, node address, PPO type, GSD, bus wiring and termination, shield grounding, drive firmware and parameters, and controlled communication and run-test results before commissioning.

Apter Power RPBA-01 3ABD64606859 Manuals and Guides

The first document is an Apter Power model-specific engineering reference. The second opens the exact manufacturer manual or datasheet for this product.

PROFIBUS-controlled motor drives

Connects a documented ABB drive to the plant PROFIBUS master for command and status exchange.

Drive reference and actual-value transfer

Carries the approved speed or torque reference and corresponding process feedback.

Drive parameter service over DP-V1

Supports authorized acyclic parameter access from a compatible engineering or control station.

Existing PROFIBUS drive replacement

Preserves node addressing, PPO mapping and bus-segment behavior during controlled drive service.

Read the applicable ABB installation instructions before work. Verify RPBA-01 3ABD64606859, the installed host system and all configured field interfaces before isolation, wiring or commissioning.

Confirm RPBA-01 and manufacturer item number 3ABD64606859 before work.

Isolate the ABB drive and wait at least five minutes for DC-link discharge.

Use ESD controls and record the installed option slot, hardware revision and connector orientation.

Record the node address, selected GSD, PPO type and process-data mapping before removal.

Inspect the D-sub connector, 34-pin drive connector, shield and protective-ground arrangement.

Confirm termination is active only at the first and last station of the PROFIBUS segment.

Restore the approved drive parameters and network configuration before controlled energization.

Verify master recognition, cyclic I/O, acyclic access, drive diagnostics and a controlled run test.

Alternative Names

RPBA-01 3ABD64606859

Technical notes

Fit RPBA-01 only in the documented drive option slot and reproduce the recorded PROFIBUS address, PPO type, baud-rate detection, GSD and process-data mapping. De-energize the drive, wait for DC-link discharge, preserve bus termination and shield grounding, then verify cyclic and acyclic communication before drive enable.

FAQ View All FAQ

Which ABB drives can use RPBA-01 3ABD64606859?

Use it only where the installed ABB drive documentation provides the compatible option slot and RPBA-01 support. Confirm the drive type, control-board execution, firmware and option-slot assignment before installation.
What network role does RPBA-01 3ABD64606859 perform?

It operates as a PROFIBUS DP slave and exchanges control, reference, status, actual-value and parameter data with a compatible PROFIBUS DP master.
How is the station address set for RPBA-01 3ABD64606859?

Record the approved node assignment and reproduce it using the module address controls or the supported configuration method. The documented station address range is 0 to 126, while the rotary-switch range is 00 to 99.
Which GSD file should be used for RPBA-01 3ABD64606859?

Match the project to the communication mode documented for the installation: ABB_0812.GSD for DP-V0 or ABB10812.GSD for DP-V1, then verify the selected PPO and I/O mapping.

How should PROFIBUS termination be checked for RPBA-01 3ABD64606859?

Termination must be active at the first and last station of the segment only. Confirm the connector termination switch, module power and shield grounding before enabling communications.
What should be recorded before replacing RPBA-01 3ABD64606859?

Record the drive and option slot, node address, GSD, PPO type, process-data map, cable routing, termination state, shield connection, hardware version and diagnostics.
How is RPBA-01 3ABD64606859 commissioned after replacement?

Restore the approved drive and master configuration, confirm master recognition, compare cyclic input and output words, verify authorized acyclic access and review both drive and network diagnostics.
Can RPBA-01 3ABD64606859 be moved to another PROFIBUS segment without verification?

No. Revalidate node uniqueness, baud-rate compatibility, cable length, termination, shield grounding, GSD, PPO mapping and the receiving control-system database before service.

Manufacturers

Supporting new and legacy automation

Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.

Please try to be as accurate as possible with your search.
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
We can't find any results for “”.