Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for 6ES7135-0HF01-0XB0
For more information on how your data is processed and stored by Apterpower please read our privacy policy
-
Match the complete marking
Include 6ES7135-0HF01-0XB0 and any revision or assembly number visible on the item. Keep the exact reference on your enquiry and quotation.
-
Check the offered item before ordering
Request available label and connector photos. Have your maintenance team compare the offered 6ES7135-0HF01-0XB0 with the installed equipment and applicable Siemens documentation.
Technical specifications for 6ES7135-0HF01-0XB0
-
Manufacturer:Siemens
-
Product Category:PLC Systems
-
Spare Part Number:6ES7135-0HF01-0XB0
-
Weight:0.25 kg
-
Tariff Code:8537101190
-
Product series:SIMATIC ET 200B
-
Product type:ET 200B Analog Output
-
Analog output channels:4
-
Network role:PROFIBUS DP slave
-
Terminal block:TB8, separate station component
-
Voltage output ranges:±10 V; 0–10 V
-
Current output ranges:±20 mA; 0–20 mA; 4–20 mA
Information
Overview
Downloads
Applications / Compatibility
Product Precautions
- Siemens 6ES7135-0HF01-0XB0 is an ET 200B-4AO analog-output station.
Field use: Send configured analog commands to process devices
Control examples: Variable-speed drives and valve positioners
Service retention: Record channel scaling and failure behavior
Control examples: Variable-speed drives and valve positioners
Service retention: Record channel scaling and failure behavior
Siemens 6ES7135-0HF01-0XB0 is an ET 200B-4AO analog-output station. It converts configured PROFIBUS DP output values into four analog field signals for compatible process devices. The PLC program, measurement range and output wiring determine the role of each channel.
The Siemens ET 200B operating instructions identify this complete order code as the 4AO execution and assign its own station identification. It is a distributed I/O unit, not an analog input card. Range selection, terminal block, bus address and supply requirements must be checked against the installed station and exact product version rather than inferred from another ET 200B module.
The analog outputs can be used in an ET 200B automation network to command suitable variable-speed drives, positioners or other analog-controlled field devices when the range and wiring match. During replacement, record the channel scaling and fail behavior, then verify each affected output against the approved control loop before handover.
The Siemens ET 200B operating instructions identify this complete order code as the 4AO execution and assign its own station identification. It is a distributed I/O unit, not an analog input card. Range selection, terminal block, bus address and supply requirements must be checked against the installed station and exact product version rather than inferred from another ET 200B module.
The analog outputs can be used in an ET 200B automation network to command suitable variable-speed drives, positioners or other analog-controlled field devices when the range and wiring match. During replacement, record the channel scaling and fail behavior, then verify each affected output against the approved control loop before handover.
Controller platform reference: SIMATIC ET 200B. Match the installed system and complete unit marking.
Technical downloads for Siemens 6ES7135-0HF01-0XB0: an Apter Power technical reference and installation verification guide.
-
Siemens 6ES7135-0HF01-0XB0 technical reference
Apter Power technical reference - PDF, 2 pages. Product identity, verified characteristics, system integration and selection checks. -
Siemens 6ES7135-0HF01-0XB0 installation guide
Apter Power installation verification guide - PDF, 2 pages. Identity, host configuration, inspection and functional release checks.
The technical reference summarizes verified product information. Confirm the installed configuration and use the applicable site procedures during installation and service.
Analog-output application: Siemens 6ES7135-0HF01-0XB0 is an ET 200B-4AO analog-output station. It receives configured PROFIBUS DP output values and delivers four analog control signals to compatible field devices.
Compatibility scope: The ET 200B station identity, PROFIBUS configuration, channel ranges and connected field inputs must match the PLC project. This is an output execution and is not interchangeable with an analog-input module.
Compatibility scope: The ET 200B station identity, PROFIBUS configuration, channel ranges and connected field inputs must match the PLC project. This is an output execution and is not interchangeable with an analog-input module.
-
Analog actuator setpoints
Send configured control signals to compatible valve positioners or actuator interfaces. Output range and scaling are defined by the station project and connected device. -
Drive speed references
Provide a scaled analog command to a drive interface that accepts the selected output range. The drive and PLC jointly determine the resulting speed action. -
Process-loop outputs
Deliver PLC-calculated values to suitable field controllers across a distributed ET 200B station. The four channels can serve independently configured control functions. -
ET 200B station maintenance
Restore the documented 4AO station with matching bus and output configuration. Keep the full 6ES7135-0HF01-0XB0 code when comparing replacements.
Installation and commissioning checks for Siemens 6ES7135-0HF01-0XB0. Prevent unintended field actions while restoring the four analog outputs.
Identify the station
Confirm the full 6ES7135-0HF01-0XB0 marking and configured ET 200B position. Record the station address and used output channels.
Make outputs safe
Isolate or hold connected actuators and field circuits under the site procedure. Prevent a transient output from moving equipment during exchange.
Preserve channel wiring
Label and photograph each analog output and return conductor. Keep shield and reference arrangements with the correct channel.
Restore output ranges
Compare the PLC configuration, output type and scaling for all four channels. Confirm that each connected device accepts the selected signal.
Protect connectors
Use electrostatic-discharge precautions and inspect station plugs, retention and cable strain relief. Refit the module without bending contacts.
Test commanded values
Apply safe test setpoints and verify measured output values and field response channel by channel. Check PROFIBUS and station diagnostics before release.
Alternative Names
Siemens 6ES7135-0HF01-0XB0
6ES71350HF010XB0
Technical notes
System relationship: The Siemens ET 200B operating instructions identify this complete order code as the 4AO execution and assign its own station identification. It is a distributed I/O unit, not an analog input card. Range selection, terminal block, bus address and supply requirements must be checked against the installed station and exact product version rather than inferred from another ET 200B module.
Applicability: The characteristics above describe the identified SIMATIC ET 200B execution of 6ES7135-0HF01-0XB0. Optional functions, connected devices and installed revisions must be checked against the complete marking and approved project configuration.
Technical reference: Siemens ET 200B Distributed I/O Station operating instructions, ET 200B-4AO exact order code.
FAQ View All FAQ
-
What is the product type of Siemens 6ES7135-0HF01-0XB0?ET 200B-4AO analog-output station.
-
What is the analog output channels of Siemens 6ES7135-0HF01-0XB0?4.
-
What is the distributed i/o family of Siemens 6ES7135-0HF01-0XB0?SIMATIC ET 200B.
-
What is the network role of Siemens 6ES7135-0HF01-0XB0?PROFIBUS DP slave.
-
What is the station identification of Siemens 6ES7135-0HF01-0XB0?ET 200B-4AO, Siemens order code 6ES7135-0HF01-0XB0.
-
Which host system is appropriate for Siemens 6ES7135-0HF01-0XB0?This execution belongs to SIMATIC ET 200B. Match the complete installed configuration and any revision before replacement.
-
What should be preserved before replacing Siemens 6ES7135-0HF01-0XB0?Record the full label, fitted connections and approved SIMATIC ET 200B settings. Preserve the existing wiring and configuration record.
-
How is Siemens 6ES7135-0HF01-0XB0 checked after installation?Check diagnostics and the affected et 200b analog output functions under the approved site test procedure.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.