-
Match the complete marking
Include PR6424/010-010 and any revision or assembly number visible on the item. Keep the exact reference on your enquiry and quotation.
-
Check the offered item before ordering
Request current label and body and cable-connector photos. Have your maintenance team compare the offered PR6424/010-010 with the installed equipment and applicable Emerson documentation.
Technical specifications for PR6424/010-010
-
Manufacturer:Epro
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:PR6424/010-010
-
Weight:0.75 kg
-
Tariff Code:8537101190
-
Sensor family:PR6424, 16 mm eddy-current displacement sensor
-
Mounting thread:M18 × 1.5
-
Cable construction:Armored
-
Sleeve-length code:Cx 40 mm
-
Cable arrangement:5 m total, with adapter plug; LEMO end
-
Nominal center gap:Approximately 2.7 mm, matched PR6424 system
-
Static range:±2.0 mm, matched PR6424 system
-
Dynamic range:0–1,000 µm, matched PR6424 system
-
Scale factor:4 V/mm, matched PR6424 system
-
Target:Ferromagnetic steel, standard 42CrMo4
Information
- The PR6424/010-010 probe is selected as part of a calibrated shaft-measurement chain; its installation geometry and cable route must suit the existing machine.
System dependency: Probe, cable, converter and monitor
Commissioning focus: Establish the approved cold gap
The 16 mm sensing family is used for non-contact measurement of relative shaft motion and position on a ferromagnetic target. A properly matched chain can support radial vibration, axial displacement, eccentricity or speed/key measurements, with the application determined by target geometry and monitor configuration.
Before commissioning, verify the M18 mounting position, target track, cable route and total electrical chain. Establish the required cold gap from the approved converter output, then trend the restored channel at a known machine condition and compare it with the site baseline.
-
Epro PR6424/010-010 technical reference
Apter Power technical reference - PDF, 2 pages. Product identity, verified interface data and applicability conditions. -
Epro PR6424/010-010 installation guide
Prepared by Apter Power - PDF, 1 page. Configuration review, safe installation and functional acceptance.
Compatibility scope: The probe, extension cable, converter, target material and monitor input form one calibrated chain; retain the offered mounting thread and cable execution.
Large-shaft turbine monitoring
Measure relative movement on a suitable turbine shaft with the specified target and a matched 16 mm proximity chain.Compressor axial position
Use a correctly mounted probe at an approved thrust target to monitor axial position.Hydro-machine runout
Observe shaft eccentricity or slow-roll motion when the target diameter and surface satisfy the measuring arrangement.Speed and key reference
Detect a suitable target feature when the converter and monitor are configured for a speed or key-pulse task.
Match the full PR6424/010-010 marking and the Cx 40 mm sleeve with the installed holder.
Assess the armored cable route and bend clearance before fitting.
Verify target material, diameter and surface condition at the measurement track.
Use the approved adapter, total cable length, converter and monitor channel.
Set the initial gap using the calibrated converter and project procedure.
Compare steady position, dynamic response and channel diagnostics against a known baseline.
Alternative Names
Technical notes
Technical basis: Emerson PR6424 Specifications Sheet, 16mm Eddy Current Sensor, December 2024.
Applicability: PR6424 performance figures are matched-family values. Confirm actual converter, target and installed order-code execution before applying them to a protection channel.
Mechanical selection: The Cx 40 mm sleeve and armored lead define the installed reach and cable protection. Check the available holder depth and cable passage before applying matched-chain performance values.
FAQ View All FAQ
-
Which components determine the calibrated output of PR6424/010-010?The probe, total cable, converter and target together determine the measuring-chain response; verify the complete set.
-
How can an incorrect sleeve reach affect PR6424/010-010?It can move the tip outside the intended target plane or prevent correct cold-gap adjustment; compare the installed holder and insertion depth.
-
What target condition is required for PR6424/010-010?Use an approved ferromagnetic target with suitable diameter, finish and track geometry; confirm the project-specific calibration.
-
Why is cable construction relevant when installing PR6424/010-010?The selected protection changes routing and bend constraints at the casing exit and adapter, even when the sensing family is the same.
-
How should an axial channel using PR6424/010-010 be checked?Confirm mechanical travel, cold gap, converter polarity and monitor scaling before relying on axial alarm values.
-
Can the PR6424 family rating be applied to PR6424/010-010 without checking the converter?No. Scale and operating limits are for a matched chain; confirm the exact converter and supplied execution.
-
What diagnostic checks follow replacement of PR6424/010-010?Inspect connector seating, converter supply, gap output and trend behavior at a controlled machine state.
-
What installation record should accompany PR6424/010-010?Keep the complete code, holder location, insertion depth, target track, cable chain and channel baseline.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






