Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for 330104-00-22-10-02-CN
For more information on how your data is processed and stored by Apterpower please read our privacy policy
Technical specifications for 330104-00-22-10-02-CN
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330104-00-22-10-02-CN
-
Estimated shipping dimensions:1.8x1.6x116.5cm
-
Weight:0.18 kg
-
Tariff Code:8537101190
-
Counliy of origin:USA
-
Probe body thread:M10 x 1
-
Mechanical protection:Flexible stainless-steel armor
-
Unthreaded length:0 mm
-
Overall case length:220 mm
-
Integral lead length:1.0 m
-
Connector execution:ClickLoc without protector
-
Cable execution:Standard FEP
-
Transducer series:3300 XL 8 mm
-
Matched-system linear range:2.0 mm
-
Incremental scale factor:7.87 V/mm nominal
-
Frequency response:0 to 10 kHz, +0/-3 dB
-
Recommended operating gap:1.27 mm approximately
-
Recommended gap voltage:-9 Vdc approximately
-
Probe tip material:Polyphenylene sulfide (PPS)
-
Probe case material:AISI 303 or 304 stainless steel
-
Probe cable impedance:75 Ohm triaxial
-
Minimum cable bend radius:25.4 mm
-
Minimum flat target diameter:15.2 mm
-
Minimum shaft diameter:50.8 mm
-
Recommended shaft diameter:76.2 mm
Information
Overview
Manuals
Common Applications
Product Precautions
Bently Nevada 330104-00-22-10-02-CN is a configured 3300 XL 8 mm eddy-current proximity probe. It senses shaft displacement for a matched Proximitor Sensor and machinery-protection channel.
- Detects shaft-to-bearing relative displacement without mechanical contact
- Forms the sensing element of a matched 3300 XL 8 mm transducer loop
- Carries the eddy-current probe signal through the configured triaxial lead
- Supports controlled static-gap and dynamic-response verification
330104-00-22-10-02-CN installs with 3300 XL 8 mm Proximitor Sensor, matched extension cable when required, compatible machinery-protection monitor, AISI 4140 steel target in an engineered 3300 XL 8 mm Proximity Transducer System configuration.
The commissioning workflow covers installed-hardware matching, controlled start-up and functional verification for this 3300 xl 8 mm proximity probe.
Important Notice: Confirm the complete 330104-00-22-10-02-CN marking, installed-system configuration, field connections and controlled functional test before commissioning or replacement.
Apter Power 330104-00-22-10-02-CN Manuals and Guides
Apter Power 330104-00-22-10-02-CN Product Technical Reference PDFBently Nevada 330104-00-22-10-02-CN Official Manual PDF
The first document is an Apter Power model-specific technical reference. The second supports model-specific installation, configuration and engineering verification.
Radial shaft-vibration measurementDetects shaft-to-bearing relative displacement without mechanical contact
Axial position and thrust monitoringForms the sensing element of a matched 3300 XL 8 mm transducer loop
Machine shaft centerline observationCarries the eddy-current probe signal through the configured triaxial lead
Bearing-clearance and rotor-position trendingSupports controlled static-gap and dynamic-response verification
Read the applicable Bently Nevada installation instructions before work. Verify 330104-00-22-10-02-CN and the installed 3300 XL 8 mm Proximity Transducer System configuration.
1Verify the complete 330104-00-22-10-02-CN marking and 220 mm case execution before work.
2Place the monitored machine and protection channel in the approved maintenance state.
3Protect the probe tip and keep the M10 x 1 mounting thread free of burrs and contamination.
4Route the 1.0 m lead without sharp bends, crushing, abrasion, or tensile loading.
5Keep the clickloc without protector connection clean, dry, and finger-tight.
6Match probe, extension cable, and Proximitor Sensor to the engineered system length.
7Set static gap within the approved linear region while maintaining shaft clearance.
8Verify polarity, vibration response, and alarm action before returning protection service.
Technical notes
Mount 330104-00-22-10-02-CN to the documented mechanical reach and route its 1.0 m lead without violating the published bend radius. Match total system length, establish the static gap, and prove channel polarity before service.
FAQ View All FAQ
-
How can an engineer function-test 330104-00-22-10-02-CN after installation?Apply a controlled input, reference, or limited output appropriate to 3300 xl 8 mm proximity probe, observe the system indication and diagnostics, and confirm the intended process response.
-
What should be checked if 330104-00-22-10-02-CN reports an unstable or incorrect value?Check seating, supply, grounding, shielding, matched components, mechanical installation, and the signal path before changing configuration or replacing additional hardware.
-
Can 330104-00-22-10-02-CN be replaced by a visually similar model without review?No. Verify the complete part number, electrical execution, connector arrangement, companion hardware, and approved software or rack configuration.
-
What commissioning evidence should be retained for 330104-00-22-10-02-CN?Retain the full 330104-00-22-10-02-CN identity, as-left wiring and settings, measured functional-test results, final diagnostics, and authorization to return the affected equipment to service.
-
Which installed hardware must be matched before fitting 330104-00-22-10-02-CN?Match the complete 330104-00-22-10-02-CN marking to 3300 XL 8 mm Proximitor Sensor and matched extension cable when required, then confirm the assigned 3300 XL 8 mm Proximity Transducer System position and approved system configuration.
-
How should the field connections for 330104-00-22-10-02-CN be recorded before replacement?Record terminal or connector identity, polarity, shield, cable tag, channel assignment, and the as-found diagnostic state before disconnecting 330104-00-22-10-02-CN.
-
What isolation is required before installing 330104-00-22-10-02-CN?Place radial shaft-vibration measurement in the approved maintenance state, isolate every applicable power, signal, and stored-energy source, and prove the work area safe.
-
Which configuration check is essential when commissioning 330104-00-22-10-02-CN?Restore only the approved model-specific channel, range, address, scale, or interface settings and compare them with the physical installation before enabling the process function.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.