Which installed system position is intended for TU830V1?

Install TU830V1 only in the documented ABB Advant OCS and S800 I/O termination position and compare the complete catalog marking with the approved hardware list.

What field signals or controlled function does TU830V1 handle?

Its documented role is sixteen-channel s800 i/o field termination and power distribution; preserve the assigned channel, network or controller function during service.

Which companion hardware must be matched to TU830V1?

Match TU830V1 with ABB S800 I/O module and ModuleBus base arrangement, including the documented rack, cable and project identity.

Which electrical rating must be checked before wiring TU830V1?

Verify type designation: TU830V1. Do not transfer limits from another catalog number.

What configuration should be recorded before replacing TU830V1?

Record the as-found position, conductors, addressing, firmware and software revision, then restore only the approved ABB Advant OCS and S800 I/O termination configuration.

Which isolation and handling controls apply to TU830V1?

Isolate all documented supply and field energy, use ESD controls and protect keyed connectors before handling TU830V1.

How should an engineer commission TU830V1?

Power up in a controlled sequence, review device and host diagnostics, then prove the intended s800 i/o cabinet termination function.

Can TU830V1 replace a visually similar module without an engineering review?

No automatic substitution is assumed; compare the complete catalog number, interfaces, ratings and approved system revision.

ABB TU830V1 S800 I/O extended module termination unit

Name: TU830V1
Brand: ABB
SKU: 3BSE013234R1

TU830V1

S800 I/O extended module termination unit

In Stock

Ships by Tuesday, September 22

Fast Shipping Available

Technical specifications for TU830V1

Manufacturer:

ABB

Product Category:

DCS System

Spare Part Number:

3BSE013234R1

Estimated shipping dimensions:

12.8x11.5x6.5cm

Weight:

0.3 kg

Tariff Code:

8537101190

Counliy of origin:

Sweden

Type designation:

TU830V1

Terminal block type:

Extended MTU

Channels:

Rated voltage:

50 V

Process connections:

I/O arrangement:

Single I/O

Maximum current per channel:

2 A

Maximum process-connection current:

5 A

Solid conductor:

0.2 to 4 mm2

Stranded conductor:

0.2 to 2.5 mm2; 24 to 12 AWG

Terminal torque:

0.5 to 0.6 Nm

Strip length:

7 mm

Dielectric test:

500 V AC

Fuse groups:

6.3 A

Operating temperature:

0 to 55 degC

Storage temperature:

-40 to +70 degC

Relative humidity:

5 to 95%

Ingress protection:

IP20

Mounting orientation:

Both directions at 55 degC

Information

Overview Manuals Common Applications Product Precautions

ABB TU830V1 is s800 i/o extended module termination unit. It provides sixteen-channel field termination and power distribution for a compatible ABB S800 I/O module.

Terminates sixteen S800 I/O channels
Provides fifty-six process connections
Accepts solid and stranded field conductors
Supports either mounting direction at rated temperature

TU830V1 operates with ABB S800 I/O module, ModuleBus base arrangement, field signal and power conductors, channel fuse-group distribution.

Engineered applications include S800 I/O cabinet termination, Process-signal marshalling, Field-power distribution, Termination-unit replacement.

Important Notice: Verify TU830V1 and article number 3BSE013234R1, paired S800 I/O module, terminal torque, conductor size, fuse grouping and every channel identity before removal; after installation, test insulation, continuity and assigned I/O response.

Apter Power ABB TU830V1 Manuals and Guides

Apter Power ABB TU830V1 Product and System Technical Reference PDF Apter Power ABB TU830V1 Installation and Commissioning Workbook PDF

The first document presents model-specific engineering data. The second provides a separate installation, connection, commissioning and acceptance workflow.

S800 I/O cabinet termination

Terminates sixteen process channels beside the assigned S800 I/O module.

Process-signal marshalling

Organizes cabinet wiring for analog or discrete field signals.

Field-power distribution

Distributes documented field power through protected terminal groups.

Termination-unit replacement

Restores the installed termination position while preserving conductor identity.

Read the applicable ABB instructions before work. Verify TU830V1 and the installed ABB Advant OCS and S800 I/O termination configuration.

Verify the complete TU830V1 marking and its assigned ABB Advant OCS and S800 I/O termination position before work.

Place the connected s800 i/o cabinet termination process in the approved maintenance state.

Isolate applicable power and sixteen-channel s800 i/o field termination and power distribution field energy before disconnecting conductors.

Record connector, conductor, address, firmware and software identities before removal.

Use ESD controls and protect keyed interfaces, exposed contacts and electronic assemblies.

Confirm the installed ABB S800 I/O module and ModuleBus base arrangement against the approved project.

Restore power in a controlled sequence and review device, network and host diagnostics.

Prove the intended process-signal marshalling function and retain the final test result.

FAQS

Which installed system position is intended for TU830V1?

Install TU830V1 only in the documented ABB Advant OCS and S800 I/O termination position and compare the complete catalog marking with the approved hardware list.
What field signals or controlled function does TU830V1 handle?

Its documented role is sixteen-channel s800 i/o field termination and power distribution; preserve the assigned channel, network or controller function during service.
Which companion hardware must be matched to TU830V1?

Match TU830V1 with ABB S800 I/O module and ModuleBus base arrangement, including the documented rack, cable and project identity.
Which electrical rating must be checked before wiring TU830V1?

Verify type designation: TU830V1. Do not transfer limits from another catalog number.
What configuration should be recorded before replacing TU830V1?

Record the as-found position, conductors, addressing, firmware and software revision, then restore only the approved ABB Advant OCS and S800 I/O termination configuration.
Which isolation and handling controls apply to TU830V1?

Isolate all documented supply and field energy, use ESD controls and protect keyed connectors before handling TU830V1.
How should an engineer commission TU830V1?

Power up in a controlled sequence, review device and host diagnostics, then prove the intended s800 i/o cabinet termination function.
Can TU830V1 replace a visually similar module without an engineering review?

No automatic substitution is assumed; compare the complete catalog number, interfaces, ratings and approved system revision.

Individual privacy preferences

We use cookies and similar technologies on our website and process your personal data (e.g. IP address), for example, to personalize content and ads, to integrate media from third-party providers or to analyze traffic on our website. Data processing may also happen as a result of cookies being set. We share this data with third parties that we name in the privacy settings.

The data processing may take place with your consent or on the basis of a legitimate interest, which you can object to in the privacy settings. You have the right not to consent and to change or revoke your consent at a later time. This revocation takes effect immediately but does not affect data already processed. For more information on the use of your data, please visit our privacy policy.

Below you will find an overview of all services used by this website. You can view detailed information about each service and agree to them individually or exercise your right to object.

You are under 14 years old? Then you cannot consent to optional services. Ask your parents or legal guardians to agree to these services with you.

TU830V1

Product Describe：

Ask our team:

Warranty Policy

Return Notice

Shipping Method

Parts Availability

How to order

Technical specifications for TU830V1

Technical specifications for TU830V1

Information

Information