Which installed system position is intended for NFCP501-W15 S2?

Install NFCP501-W15 S2 only in the documented Yokogawa STARDOM FCN-500 autonomous controller position and compare the complete catalog marking with the approved hardware list.

What field signals or controlled function does NFCP501-W15 S2 handle?

Its documented role is controller logic, redundant sb-bus i/o, ethernet and rs-232-c communications; preserve the assigned channel, network or controller function during service.

Which companion hardware must be matched to NFCP501-W15 S2?

Match NFCP501-W15 S2 with FCN-500 base unit and SB-bus I/O modules, including the documented rack, cable and project identity.

Which electrical rating must be checked before wiring NFCP501-W15 S2?

Verify style: S2. Do not transfer limits from another catalog number.

What configuration should be recorded before replacing NFCP501-W15 S2?

Record the as-found position, conductors, addressing, firmware and software revision, then restore only the approved Yokogawa STARDOM FCN-500 autonomous controller configuration.

Which isolation and handling controls apply to NFCP501-W15 S2?

Isolate all documented supply and field energy, use ESD controls and protect keyed connectors before handling NFCP501-W15 S2.

How should an engineer commission NFCP501-W15 S2?

Power up in a controlled sequence, review device and host diagnostics, then prove the intended autonomous process control function.

Can NFCP501-W15 S2 replace a visually similar module without an engineering review?

No automatic substitution is assumed; compare the complete catalog number, interfaces, ratings and approved system revision.

Yokogawa NFCP501-W15 S2 STARDOM FCN-500 processor module

Name: NFCP501-W15 S2
Brand: Yokogawa
SKU: NFCP501-W15 S2

NFCP501-W15 S2

STARDOM FCN-500 processor module

In Stock

Ships by Tuesday, September 22

Fast Shipping Available

Technical specifications for NFCP501-W15 S2

Manufacturer:

Yokogawa

Product Category:

DCS System

Spare Part Number:

NFCP501-W15 S2

Estimated shipping dimensions:

6.5x15x13cm

Weight:

0.9 kg

Tariff Code:

8537101190

Counliy of origin:

Japan

CPU:

Intel Atom E3815, 1.46 GHz

Style:

Main memory:

256 MB with ECC

SRAM:

2 MB with ECC, battery backed

Onboard flash:

1 GB

SD card:

SDHC 4 to 32 GB, Class 10

Ethernet ports:

2 RJ45

Ethernet speed:

10/100/1000 Mbit/s

Serial interface:

RS-232-C, D-sub 9-pin male

Serial rate:

Up to 115.2 kbit/s

Serial mode:

Asynchronous, full- or half-duplex

I/O bus:

Redundant SB bus

Diagnostics:

Watchdog timer and temperature monitoring

Battery capacity:

1000 mAh

Supply:

5 V DC +/-5%

Current consumption:

1200 mA maximum

Rack occupancy:

2 slots

Duplex operation:

Supported

Information

Overview Manuals Common Applications Product Precautions

Yokogawa NFCP501-W15 S2 is stardom fcn-500 processor module. It executes autonomous control logic, coordinates redundant SB-bus I/O and provides Ethernet and serial communications for an FCN-500 station.

Uses a 1.46 GHz Intel Atom processor
Supports duplex processor operation
Provides two gigabit-capable Ethernet ports
Coordinates redundant SB-bus field I/O

NFCP501-W15 S2 operates with FCN-500 base unit, SB-bus I/O modules, SDHC engineering card, STARDOM engineering and network configuration.

Engineered applications include Autonomous process control, Remote utility station automation, Redundant field control node, FCN-500 processor renewal.

Important Notice: Verify NFCP501-W15 S2, processor operating mode, Ethernet addresses, serial parameters, SB-bus configuration, SDHC contents and battery condition before replacement; confirm duplex synchronization and all controller diagnostics after restart.

Apter Power Yokogawa NFCP501-W15 S2 Manuals and Guides

Apter Power Yokogawa NFCP501-W15 S2 Product and System Technical Reference PDF Apter Power Yokogawa NFCP501-W15 S2 Installation and Commissioning Workbook PDF

The first document presents model-specific engineering data. The second provides a separate installation, connection, commissioning and acceptance workflow.

Autonomous process control

Executes local control at remote or unattended process sites.

Remote utility station automation

Coordinates water, energy or infrastructure station signals.

Redundant field control node

Maintains controller availability through a duplex processor arrangement.

FCN-500 processor renewal

Restores processor service while preserving network and I/O identities.

Read the applicable Yokogawa instructions before work. Verify NFCP501-W15 S2 and the installed Yokogawa STARDOM FCN-500 autonomous controller configuration.

Verify the complete NFCP501-W15 S2 marking and its assigned Yokogawa STARDOM FCN-500 autonomous controller position before work.

Place the connected autonomous process control process in the approved maintenance state.

Isolate applicable power and controller logic, redundant sb-bus i/o, ethernet and rs-232-c communications field energy before disconnecting conductors.

Record connector, conductor, address, firmware and software identities before removal.

Use ESD controls and protect keyed interfaces, exposed contacts and electronic assemblies.

Confirm the installed FCN-500 base unit and SB-bus I/O modules against the approved project.

Restore power in a controlled sequence and review device, network and host diagnostics.

Prove the intended remote utility station automation function and retain the final test result.

FAQS

Which installed system position is intended for NFCP501-W15 S2?

Install NFCP501-W15 S2 only in the documented Yokogawa STARDOM FCN-500 autonomous controller position and compare the complete catalog marking with the approved hardware list.
What field signals or controlled function does NFCP501-W15 S2 handle?

Its documented role is controller logic, redundant sb-bus i/o, ethernet and rs-232-c communications; preserve the assigned channel, network or controller function during service.
Which companion hardware must be matched to NFCP501-W15 S2?

Match NFCP501-W15 S2 with FCN-500 base unit and SB-bus I/O modules, including the documented rack, cable and project identity.
Which electrical rating must be checked before wiring NFCP501-W15 S2?

Verify style: S2. Do not transfer limits from another catalog number.
What configuration should be recorded before replacing NFCP501-W15 S2?

Record the as-found position, conductors, addressing, firmware and software revision, then restore only the approved Yokogawa STARDOM FCN-500 autonomous controller configuration.
Which isolation and handling controls apply to NFCP501-W15 S2?

Isolate all documented supply and field energy, use ESD controls and protect keyed connectors before handling NFCP501-W15 S2.
How should an engineer commission NFCP501-W15 S2?

Power up in a controlled sequence, review device and host diagnostics, then prove the intended autonomous process control function.
Can NFCP501-W15 S2 replace a visually similar module without an engineering review?

No automatic substitution is assumed; compare the complete catalog number, interfaces, ratings and approved system revision.

Individual privacy preferences

We use cookies and similar technologies on our website and process your personal data (e.g. IP address), for example, to personalize content and ads, to integrate media from third-party providers or to analyze traffic on our website. Data processing may also happen as a result of cookies being set. We share this data with third parties that we name in the privacy settings.

The data processing may take place with your consent or on the basis of a legitimate interest, which you can object to in the privacy settings. You have the right not to consent and to change or revoke your consent at a later time. This revocation takes effect immediately but does not affect data already processed. For more information on the use of your data, please visit our privacy policy.

Below you will find an overview of all services used by this website. You can view detailed information about each service and agree to them individually or exercise your right to object.

You are under 14 years old? Then you cannot consent to optional services. Ask your parents or legal guardians to agree to these services with you.

NFCP501-W15 S2

Product Describe：

Ask our team:

Warranty Policy

Return Notice

Shipping Method

Parts Availability

How to order

Technical specifications for NFCP501-W15 S2

Technical specifications for NFCP501-W15 S2

Information

Information