-
Match the complete marking
Provide the complete PR6424/01 CS CON021 marking, clear installed-position photographs and the identities of connected carrier, termination or sensing components.
-
Check the offered item before ordering
Compare the offered PR6424/01 CS CON021 execution, connector or terminal arrangement and included items with the approved drawing before ordering.
Technical specifications for PR6424/01 CS CON021
-
Manufacturer:Epro
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:PR6424/01 CS CON021
-
Weight:0.46 kg
-
Tariff Code:8537101190
-
Sensor family:PR6424 16 mm eddy-current sensor
-
Companion converter:CON021
-
Sensitivity:4 V/mm (101.6 mV/mil), linearity <= +/-1.5%
-
Nominal center air gap:Approximately 2.7 mm
-
Static range:+/-2.0 mm
-
Dynamic range:0 to 1000 um
-
Minimum shaft diameter:80 mm
-
Reference target:42CrMo4 ferromagnetic steel
-
Maximum surface speed:2500 m/s
-
Sensor operating temperature:-35 to +150 deg C
-
Pressure resistance, sensor head:10000 hPa (145 psi)
-
Sensor sleeve material:Stainless steel
-
Sensor cable material:PTFE
-
Converter frequency range:0 to 20 kHz (-3 dB)
-
Converter rise time:<15 us
-
Converter supply, -4 to -20 V output:-23 to -32 V DC
-
Converter supply, -2 to -18 V output:-21 to -32 V DC
-
Converter operating temperature:-30 to +100 deg C
-
Converter protection class:IP20
-
Converter mounting:Panel mount with four M5 x 20 screws
Information
- PR6424/01 CS CON021 combines the PR6424 sensing geometry with the CON021 converter interface for non-contact shaft displacement and vibration measurement.
Matched sensor-converter scaling: Sensor sensitivity and converter output form one calibrated electrical relationship rather than independent components.
Panel-mounted signal conditioning: The converter provides a high-bandwidth negative-voltage output for machinery protection or monitoring channels.
Published range and scale values use the stated 42CrMo4 reference target. Shaft material, diameter, runout, nearby conductive surfaces and cable-converter pairing can change the installed response and must be controlled.
Before exchange, record sensor insertion, locknut position, cable route, converter terminals, static output and machine baseline. Restore the complete chain, set the approved gap, then compare static and dynamic response before release.
PR6424/01 CS CON021 Official Technical Excerpt
Emerson PR6424 16 mm Eddy Current Sensor Specifications Sheet, December 2024. Selected original pages covering the applicable product family, ratings and hardware relationship.PR6424/01 CS CON021 Installation & Verification Guide
Model-specific field guide for identity capture, controlled exchange, commissioning evidence, fault isolation and handover.
Application scope: Use PR6424/01 CS CON021 for non-contact shaft vibration, axial position, eccentricity or speed/key measurement where its range, target geometry and hazardous-area design match the approved machine installation.
Radial shaft vibration
Measure shaft-relative motion within the documented 4 mm static sensor range.Axial position monitoring
Set the static operating point so expected thrust travel remains inside the calibrated region.Eccentricity and runout
Retain the same target material, surface condition and mechanical datum for comparison.Speed or key reference
Confirm target geometry and receiving-channel threshold for the intended pulse response.
Photograph PR6424/01 CS CON021, including every slash, suffix and converter marking.
Measure insertion, locknut position, target clearance and cable orientation before removal.
Keep the tip away from impact, chips, moisture and unsupported side load.
Retain the documented CON021 pairing and material calibration for this sensor chain.
Use the approved negative-voltage output and machine drawing rather than mechanical clearance alone.
Compare static output, runout and representative dynamic response with the accepted baseline.
Alternative Names
Technical notes
Exact execution: PR6424 sensor reference with CON021 signal converter
Calibration boundary: Range and sensitivity depend on matched sensor, converter, target material and installed geometry
Technical reference: Emerson PR6424 16 mm Eddy Current Sensor Specifications Sheet, December 2024; Emerson CON021 Specifications Sheet
FAQ View All FAQ
-
Which installed dimensions must be captured for PR6424/01 CS CON021?Record thread engagement, insertion depth, locknut position, target clearance, shaft diameter and nearby conductive geometry.
-
Why must the CON021 stay matched to PR6424/01 CS CON021?Sensor sensitivity, material calibration and converter output range form one measurement chain; an arbitrary converter can change scale and linearity.
-
Which target assumptions apply to PR6424/01 CS CON021?Published values use 42CrMo4 ferromagnetic steel; verify actual shaft material, surface finish and diameter before applying the catalog scale.
-
How should the operating gap of PR6424/01 CS CON021 be restored?Use the approved live converter output and documented mechanical datum, then confirm expected travel remains within the calibrated region.
-
What cable handling is required for PR6424/01 CS CON021?Support the cable independently, respect the sensor-family bend radius and prevent twisting at the sensor or converter connector.
-
How is runout separated from vibration for PR6424/01 CS CON021?Record slow-roll mechanical and electrical runout first, then compare operating response with that baseline.
-
Which converter checks add technical value for PR6424/01 CS CON021?Verify negative supply voltage, terminal identity, static output, grounding or barrier arrangement and receiving-channel polarity.
-
What proves PR6424/01 CS CON021 is ready for service?Accept the mechanical datum, stable static output, slow-roll runout and representative vibration or position response as one documented channel.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






