-
Match the complete marking
Include PR6423/002-121 CON041 and any revision or assembly number visible on the item. Keep the exact reference on your enquiry and quotation.
-
Check the offered item before ordering
Request available label and connection photos. Have your maintenance team compare the offered PR6423/002-121 CON041 with the installed equipment and applicable manufacturer documentation.
Technical specifications for PR6423/002-121 CON041
-
Manufacturer:Emerson
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:PR6423/002-121 CON041
-
Weight:0.15 kg
-
Tariff Code:8537101190
-
Sensor family:PR6423, 8 mm eddy-current probe
-
Converter family:CON041
-
Measurement principle:Noncontact eddy-current displacement
-
Sensor execution:PR6423/002-121
-
Converter identity:CON041; match actual label
-
System boundary:Probe, converter, cable and target form the measurement chain
-
PR6423 linear range:2 mm
-
PR6423 initial gap:0.5 mm
-
PR6423 scale factor:8 V/mm ±5% at 0 to 45 °C
-
PR6423 target diameter:25 mm minimum
-
PR6423 target material:42CrMo4 (AISI/SAE 4140) reference
-
PR6423 ingress protection:IP66
-
PR6423 sensor tip:PEEK
Information
- The selected probe and converter measure relative shaft displacement after the complete chain is matched and calibrated.
Signal handoff: Check conditioned converter output at the intended monitor input
Service record: Retain the initial gap and pre-service signal baseline
The PR6423 family uses an 8 mm probe tip and is applied to shaft vibration, axial position and related relative displacement measurements. CON041 is a matching eddy-current signal-converter family. The exact /002-121 probe option and converter execution must be checked against the supplied labels before assigning family ratings to the offered combination.
During replacement, retain the mechanical target track, mounting position and cable route. Set the initial probe gap using the approved converter output and compare the restored signal with the pre-service baseline before enabling machinery protection.
-
Emerson PR6423/002-121 CON041 technical reference
Apter Power technical reference - PDF, 2 pages. Verified product identity, system role, configuration boundaries and engineering checks. -
Emerson PR6423/002-121 CON041 installation guide
Prepared by Apter Power - PDF, 1 page. Identification, installation preparation, configuration and acceptance checks.
Compatibility scope: Match the PR6423 probe, extension cable, CON041 converter, target material and monitor input as one calibrated chain.
Radial shaft vibration
Measure shaft motion relative to a bearing housing with a matched PR6423/CON041 chain.Axial position monitoring
Track thrust movement using an approved target face and calibrated axial probe arrangement.Slow-roll diagnostics
Observe target runout or eccentricity with a suitable monitor and machine reference.Machinery protection input
Provide conditioned displacement information to the installed protection channel after approved chain calibration.
Compare PR6423/002-121 and CON041 with both offered labels and the installed channel.
Review target material, surface condition and probe track.
Match extension cable, connector and total cable arrangement.
Avoid impact on the tip and over-bending the cable at its casing exit.
Use the approved converter voltage and site gap-setting procedure.
Compare the steady gap and dynamic response against the baseline.
Alternative Names
Technical notes
Technical basis: Emerson PR 642x eddy-current sensor specifications and CON041 signal-converter product information.
Applicability: PR6423 and CON041 family descriptions establish the measurement roles; option-specific ratings for /002-121 are reserved for the supplied labels and approved chain configuration.
Commissioning evidence: Compare pre-service and post-service I/O or controller diagnostics, record the affected points, and retain the signed site acceptance result for PR6423/002-121 CON041.
FAQ View All FAQ
-
Why is converter matching important for PR6423/002-121 CON041?The PR6423 probe, cable and CON041 converter form a calibrated chain; changing one component can alter sensitivity or baseline.
-
What can cause a baseline shift after fitting PR6423/002-121 CON041?Check probe gap, target track, cable continuity and converter setting before changing alarm limits.
-
How should shaft target condition be assessed for PR6423/002-121 CON041?Inspect material, surface finish, deposits and runout at the measurement track.
-
Can PR6423/002-121 CON041 be used as a stand-alone vibration transmitter?The complete measurement requires the matched converter and appropriate monitoring input.
-
What should be recorded before removing PR6423/002-121 CON041?Record probe insertion depth, target position, total cable path, converter identity and monitored gap voltage.
-
How can an intermittent signal from PR6423/002-121 CON041 be isolated?Inspect connector seating, cable damage, converter power and target movement under controlled conditions.
-
How should the initial gap be set for PR6423/002-121 CON041?Use the applicable converter output and machine procedure rather than a visual gap estimate.
-
What acceptance test should follow installation of PR6423/002-121 CON041?Compare stable gap output and dynamic channel behavior with an approved machine condition before returning protection to service.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.





