
Understanding Bently Nevada 21000 and 24701 Proximity Probe Housing Assemblies
The Bently Nevada 21000 and 24701 are all-metal housings for externally mounted proximity probes. The 21000 has an aluminum body, while the 24701 has a 303 stainless steel body. Both use a 304 stainless steel probe sleeve.
Body material is only the first selection point. A correct replacement also depends on the complete order number, probe and cable selection, standoff and penetration dimensions, conduit fittings, mounting thread, machine geometry, and required approvals. A matching family number does not establish interchangeability.
These housings provide external access to the probe and its cable connection for gap adjustment or probe replacement. The housing supports and protects the probe, but the complete proximity transducer chain performs the measurement. The extension cable, Proximitor Sensor, and monitor remain separate unless the quote expressly includes them.
The Installed Housing Defines the Replacement Requirements
At Apter Power, we treat the base family as the starting point, not as proof of a replacement match. The installed label and machine records establish what the current assembly contains and how it fits the machine.
A useful identification record includes:
- Complete 21000 or 24701 part number, including every suffix field
- Any MOD number or special project marking
- Clear photographs of the housing label, probe label, cable entry, and mounting interface
- Installed probe family and cable length
- Standoff, penetration, fittings, and mounting thread
- Machine drawing or measured mounting geometry
- Required hazardous area and end-user country approvals
A MOD marking requires separate review because a standard catalog suffix may not describe every mechanical or supply detail. A visually similar standard assembly should not be treated as equivalent to a modified unit.
The 21000 and 24701 Differ in More Than Housing Material
The Bently Nevada housing datasheet 141600 identifies the fixed material difference and the configurable parts of each assembly.
| Selection Point | 21000 | 24701 | Replacement Consequence |
|---|---|---|---|
| Housing body | Aluminum | 303 stainless steel | The replacement must satisfy the documented material requirement. |
| Probe sleeve | 304 stainless steel | 304 stainless steel | The shared sleeve material does not make the housings interchangeable. |
| Typical mass without fittings | 1.1 kg or 2.4 lb | 1.8 kg or 4.1 lb | The installed support and project specification may limit acceptable mass. |
| Basic function | External mounting and access for a reverse-mount proximity probe | External mounting and access for a reverse-mount proximity probe | Both families serve the same broad function. |
| Order format | 21000-AA-BB-CC-DDD-EE-FF | 24701-AA-BB-CC-DDD-EE-FF | The value in every field must match the required configuration. |
The datasheet does not rank one family as universally better. The 24701 stainless steel body does not override the machine drawing, mounting interface, project material specification, or approval requirement. The 21000 remains the correct family when the installed design requires its aluminum housing and matching configuration.
The Complete Ordering Number Defines the Supplied Assembly
The six suffix fields define what the assembly contains and how it connects to the machine. The two families use the same field sequence, but their available values are not identical.
| Field | Configuration Defined by the Field | Required Check |
|---|---|---|
| A | Probe type, connector arrangement, and available approval option | Probe family and approval marking |
| B | Probe cable length | Usable lead length relative to sleeve reach |
| C | Standoff adapter dimension | Clearance above the machine case |
| D | Probe penetration dimension | Required reach from the mounting arrangement toward the target |
| E | Conduit fittings, plugs, reducers, and cable seal arrangement | Cable entry, sealing, and approval configuration |
| F | Machine mounting thread | Thread type, engagement, and mechanical interface |
The current Rev. AC ordering information presents probe options for 3300 XL 8 mm, 3300 XL NSv, and 3300 XL 11 mm reverse-mount probes, with approval and connector protector variants for selected configurations. Probe code 00 allows an assembly to be ordered without a probe, while cable code 00 indicates that a probe cable is not required in that configuration.
One Complete 21000 Number Shows How the Fields Work
A representative configuration, 21000-16-05-00-105-03-02, breaks down as follows:
- 21000: aluminum housing family
- 16: 3300 XL 8 mm reverse-mount probe
- 05: 0.5 m probe cable
- 00: no standoff adapter
- 105: 10.5 in probe penetration
- 03: one plug, one reducer, and a cable seal grip
- 02: 3/4-14 NPT machine mounting thread
Another 21000 can have no supplied probe, a different cable length, a standoff adapter, another penetration dimension, different fittings, or another mounting thread.
Probe Reach Must Match the Machine Geometry
The selected probe must reach the target without creating an unsupported or incorrectly positioned sleeve. The machine drawing therefore governs the C and D dimensions.
The current Rev. AC ordering information sets several limits that affect the installation:
- The probe lead must be longer than the sleeve.
- A combined C plus D dimension greater than 300 mm or 12 in requires sleeve support near the probe to prevent resonance.
- A penetration length between 1.0 and 2.0 in may require a counterbore to reduce probe side view or rear view effects.
- Probe penetration option D has an adjustment range of approximately ±13 mm or ±0.5 in.
- The maximum C plus D value depends on the selected probe cable length and housing family.
These limits make cable length, sleeve length, and target position one mechanical selection problem. A longer penetration code does not solve a clearance problem when the probe lead is too short or the sleeve lacks support.
The installed gap still requires the applicable probe system procedure and a calibrated measurement chain. The housing order number defines the mechanical arrangement; it does not replace gap setting, commissioning, or site safety controls.
Hazardous Area Approval Depends on the Complete Configuration
The housing specification, explosion-proof approval, and intrinsically safe probe circuit describe different compliance boundaries. The complete configuration determines which claim applies.
| Term | What It Establishes | What It Does Not Establish |
|---|---|---|
| API 670 compliance | The manufacturer identifies the housings as compliant with API 670 requirements for externally mounted proximity probe housings. | API 670 compliance does not prove that a specific order is explosion-proof. |
| CSA Type 4 enclosure | The enclosure has the stated environmental enclosure classification. | Type 4 does not make every 21000 or 24701 order a CA explosion-proof housing. |
| CA21000 or CA24701 | The specified CA housing can carry the documented CSA explosion-proof approval when ordered in an allowed configuration. | A CA housing designation does not establish the approval of every probe circuit or installation. |
| Intrinsically safe probe circuit | The approved probe, barriers, wiring, and installation satisfy the applicable intrinsic safety design. | An approved probe circuit does not make a standard housing explosion-proof. |
The Rev. AC ordering note states that only CA versions are CSA rated as explosion-proof when ordered with fitting options E00, E01, E02, or E04. Fitting option E03 includes a plug, reducer, and cable seal grip, but that hardware does not convert a standard housing into a CA explosion-proof assembly.
The manufacturer also states that CA housings are limited to North American end users. The end-user country, current certificate set, probe approval, fitting option, and complete installed circuit therefore belong in the approval review.
A Complete RFQ Prevents Configuration Mismatches
A complete request allows engineering and purchasing teams to compare the same configuration. The RFQ should attach the identification record described above and add the commercial requirements that are not part of equipment identification:
- Required quantity and acceptable product condition
- Required delivery date and final destination
- Required offered-unit photographs, inspection records, certificates, or traceability documents
The resulting quote should identify the offered part number, included probe and fittings, product condition, document scope, availability, and estimated ship date. Those details make the offer reviewable before a purchase order is released.
FAQs
Q1. What Should Be Checked When the Assembly Arrives?
Receiving inspection should match the complete order number, MOD marking, quantity, condition, included probe, cable, fittings, mounting thread, and documents against the quote. Our parts verification guide covers the evidence that should be checked again on arrival. Any difference requires written resolution before the assembly is released for installation.
Q2. Which Documents Should Support a Hazardous Area Configuration?
The review should include the current housing datasheet, the applicable Bently Nevada Approvals Quick Reference Guide entry for the end-user country, the probe system manual, and the installed circuit or barrier drawing. The quote and label photos show what was supplied; they do not replace site approval of the complete installation.
Q3. Which Temperature Limit Governs a Housing Assembly?
The selected probe determines the applicable temperature limit. Rev. AC specifies an operating and storage range of -51°C to +177°C for 3300 XL 8 mm and 11 mm probes. The 3300 XL NSv range is -34°C to +177°C in operation and -51°C to +177°C in storage. The exact probe configuration and current probe manual govern the final limit.
Apter Power Can Review the Complete Configuration Before a Quote
Apter Power can review the completed identification and RFQ records before preparing a quote.
A review request can be sent to sales13@apterpower.com with the completed RFQ record and required delivery date. Our how to order guide explains how the inquiry, quote, and order confirmation fit together before a purchase order is released.

Plan your automation parts enquiry
-
12-Month Warranty
-
Fast Worldwide Dispatch
-
ISO 9001:2015 certified

One part or a full list. Start here.
Share your parts list, quantities and required date.
Email your parts list



