Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for 330980-50-00
For more information on how your data is processed and stored by Apterpower please read our privacy policy
Technical specifications for 330980-50-00
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330980-50-00
-
Estimated shipping dimensions:8×6×6.5cm
-
Weight:0.22 kg
-
Tariff Code:8537101190
-
Counliy of origin:USA
-
Product Family:3300 XL NSv Proximitor Sensor
-
Electrical System Length:50 = 5.0 m system
-
Mounting Selection:50 = panel mount
-
Approval Option:00 = agency approval not required
-
Sensor Input:One 3300 RAM or NSv probe and extension cable
-
Terminal Strip:SpringLoc
-
Factory Calibration Target:AISI 4140 steel
-
Supply without Barriers:-17.5 to -26 VDC
-
Supply with Barriers:-23 to -26 VDC
-
Maximum Current Consumption:12 mA
-
Supply Sensitivity:Less than 2 mV output change per volt of supply change
-
Output Resistance:50 ohm
Information
Overview
Manuals
Common Applications
Product Precautions
Bently Nevada 330980-50-00 is the panel-mount signal conditioner at the electronic end of a five-metre 3300 XL NSv channel. It supplies the probe, linearizes the gap signal and presents a low-impedance voltage output for the receiving monitor.
- Conditions one matched five-metre NSv probe-and-extension chain.
- Uses the panel-mount execution selected by code 50.
- Provides SpringLoc field terminals and a low-impedance conditioned output.
- Selects no agency-approval option through the final 00 code.
The sensor completes the electronic end of an NSv proximity channel. Preserve its mounting isolation, negative DC supply, target calibration and five-metre electrical chain when moving or replacing the device.
Important Notice: Panel mounting and five-metre calibration are part of the 50 selection. Use the matched NSv components and do not transfer the larger XL 8 mm system range to this channel.
Bently Nevada 330980-50-00 Manuals & Downloads
Bently Nevada 330980-50-00 Official Technical Reference (PDF)Bently Nevada 330980-50-00 Installation & Commissioning Guide (PDF)
The Technical Reference organizes the exact ordering identity, applicable characteristics and system boundary for this proximitor sensor. The Installation & Commissioning Guide covers identification, pre-installation checks, connections, functional verification and the acceptance record.
Small-shaft vibration
Condition a matched NSv probe signal on compressors, pumps and auxiliary machines with tight clearances.
Static shaft position
Provide a voltage proportional to target distance across the rated NSv linear range.
Panel-mounted sensor banks
Install the compact conditioner on its isolation pad in a traditional panel layout.
Rotational reference channels
Support suitable speed or phase-reference measurements when the target arrangement is configured for that use.
Apply these checks to the exact Bently Nevada 330980-50-00 item before returning its monitoring path to service.
1
Match the probe and extension cable to the five-metre 330980-50-00 calibration.
2
Retain the panel-mount isolation pad; grounding the housing can change the intended installation.
3
Apply the specified negative DC supply and verify voltage at the sensor under load.
4
Keep IN, OUT and COM conductors identified at the SpringLoc terminals.
5
Confirm the target and static gap against NSv calibration rather than XL 8 mm values.
6
Protect probe and extension connectors from contamination and accidental grounding.
7
Review barrier requirements separately if the installed circuit uses intrinsic-safety interfaces.
8
Record the static output and machine response before returning the channel to service.
Technical notes
Panel mounting and five-metre calibration are part of the 50 selection. Use the matched NSv components and do not transfer the larger XL 8 mm system range to this channel.
FAQ View All FAQ
-
What does 50 select on 330980-50-00?It selects a 5.0 m electrical system and panel mounting.
-
Does 330980-50-00 mount on a 35 mm DIN rail?No. Code 50 is the panel-mount execution; code 51 is the five-metre DIN version.
-
Which probe family is paired with 330980-50-00?Use a matched 3300 XL NSv probe and extension cable.
-
What linear range should be used for 330980-50-00?Use the NSv system's 1.5 mm range, approximately 0.25 to 1.75 mm from the target, under the stated operating conditions.
-
Why is the mounting pad important for 330980-50-00?The panel-mount isolation pad preserves the intended electrical isolation and mechanical installation.
-
How should supply voltage be checked at 330980-50-00?Measure the negative DC supply at the sensor under load and apply the barrier-specific limit if barriers are installed.
-
Does 330980-50-00 include an agency approval?No. The final 00 means agency approval is not required in the ordering code.
-
What should be tested after replacing 330980-50-00?Verify the complete five-metre chain, supply, static gap voltage, monitor scaling and dynamic machine response.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.